How to fix 'Error, front cap' on HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, front cap', it may be due to residues of cable ties trapped behind the front cap. Clean the front sensor. Another possible cause is a busy level sensor. If applicable, carefully remove any cable-tie residues.
What to do if HellermannTyton Autotool 2000 CPK display 'Error, gate'?
If your HellermannTyton Tools display shows 'Error, gate', it may be because the drum is not in the correct position. To resolve this, open the gate and turn the drum to the correct position. Alternatively, the gate may simply be open; in that case, close it.
How to troubleshoot 'Error, drum' on HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, drum', it could be because the cable tie bandoleer is pulled in at an angle. Refer to the instructions for opening the two transparent flaps at the gate. Another possibility is that the roller lever drum is jammed or defective, in which case you should open the roller lever drum and turn the drum to the correct position.
What causes 'Error, start position' on HellermannTyton Autotool 2000 CPK, and how can I fix it?
If your HellermannTyton Tools display shows 'Error, start position', it may be because the AT2000 CPK is not in the start position. Push the actuator for the bandoleer cutter to the left. Other possible solutions include opening and closing the gate, carefully removing any cable-tie residues, and pressing the Reset button.
Why is the cable tie not cut off flush by my HellermannTyton Tools?
If the cable tie is not cut off flush by your HellermannTyton Tools, the cutter in the front cap may not be in the correct position. Check the position of the cutter in the front cap and remove any cable-tie residues.
What does 'Error, tensioning motor' mean on my HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, tensioning motor', the drive might be jammed or defective. If applicable, carefully remove any cable-tie residues.
Why are loops forming when using my HellermannTyton Tools?
If your HellermannTyton Tools are forming loops, it could be because the bundle diameter is unsuitable. Use a suitable bundle diameter.
Why is binding not possible with my HellermannTyton Autotool 2000 CPK?
If binding is not possible with your HellermannTyton Tools, the upper jaw may be blocked. Check the upper jaw.
What does 'Error, binding force' mean on HellermannTyton Autotool 2000 CPK?
If your HellermannTyton Tools display shows 'Error, binding force', the specified binding force is not being achieved. Check the binding.
What to do if my HellermannTyton Tools show an 'Overload' error?
If your HellermannTyton Tools display shows 'Overload', it could be due to a blocked drum. Refer to the instructions for opening the two service flaps at the gate. Alternatively, the bandoleer cutter might not be cutting the cable ties, or the cable tie bandoleer is pulled in at an angle, so try pressing the Reset button.
General| Type | Autotool 2000 CPK |
|---|---|
| Application Method | Pneumatic |
| For Cable Diameter Max. | 20 mm |
| Bundling Diameter max. | 20 mm |
| Tensile Strength min. | 80 N |
| Tensioning | Automatic |
| Tension Force | Adjustable |
| Tie Width | 4.5 mm |
| Cable Tie Width | 4.5 mm |
| Material Shortcut | PA66 |
| Operating Temperature | -40°C to +85°C |
| Tool Included | Yes |
| Pack Quantity | 1 |
| Cutting Mechanism | Automatic |
| Cutting System | Flush cut |
| Power Supply | Pneumatic |
| Operating Pressure | 6 bar |
| Material | Nylon 6.6 |
To Next Page
