2-8
Item
Thread dia. (mm)
Torque value
and pitch (length)
N
.
m kgf
.
m lbf
.
ft
• ENGINE
Mounting case bolt M12 x 1.25 64 6.5 47
M10 x 1.25 44 4.5 33
M8 x 1.25 26 2.7 20
Mounting case nut M10 x 1.25 44 4.5 33
Plug hole coil bolt M6 x 1.0 12 1.2 9
Flywheel boss bolt M8 x 1.25 32 3.3 24
Flywheel bolt M12 x 1.0 118 12.0 87
Alternator bolt M10 x 1.25 44 4.5 33
nut M8 x 1.25 26 2.7 20
Alternator pulley lock nut M14 x 1.5 110 11.2 81
Starter motor bolt M10 x 1.25 44 4.5 33
Starter motor front bracket screw M5 screw 2.5 0.25 1.8
Starter motor bolt screw M5 5 0.5 3.6
Starter solenoid switch screw M6 screw 6 0.6 4.3
EOP switch (Low pressure side) PT 1／880.8 5.8
EOP switch (High pressure side) M10 x 1.25 22 2.2 16
ECT sensor M10 x 1.25 12 1.2 9
A/F sensor M18 x 1.5 42 4.3 31
Knock sensor M12 x 1.25 31 3.2 23
MAP sensor bolt M5 x 0.8 3.4 0.35 2.5
ECM bolt M6 x 1.0 5 0.5 3.6
Intake manifold bolt, nut M8 x 1.25 26 2.7 20
Exhaust manifold bolt M10 x 1.25 39 4.0 29
Exhaust guide bolt M8 x 1.25 26 2.7 20
Water separator body screw M5 screw 3.4 0.35 2.5
Fuel strainer body screw M5 screw 3.4 0.35 2.5
Fuel pump (low pressure side) bolt M6 x 1.0 12 1.2 9
Vapor separator assembly bolt M8 x 1.25 26 2.7 20
Vapor separator stay bolt M8 x 1.25 26 2.7 20
Service check bolt M6 x 1.0 12 1.2 9
Vapor separator cover screw M5 screw 3.4 0.35 2.5
Water jacket cover screw M5 screw 3.4 0.35 2.5
Strainer cover screw M5 screw 3.4 0.35 2.5
Pump cover screw M5 screw 3.4 0.35 2.5
Pump harness assembly screw M4 screw 2.1 0.21 1.5
Float pin screw 2.1 0.21 1.5
Fuel pump case bolt M6 x 1.0 12 1.2 9
Plate stay A bolt M6 x 1.0 12 1.2 9
• GEAR CASE
Propeller shaft holder bolt M10 x 1.25 34 3.5 25
18 mm castle nut (*1) M18 x 1.5 1 0.1 0.7
Gear case bolt M10 x 1.25 34 3.5 25
Oil level bolt M8 x 1.25 3.4 0.35 2.5
Oil drain bolt M8 x 1.25 3.4 0.35 2.5
Water screen screw M5 x 0.8 1 0.1 0.7
Sensor nipple M8 x 1.0 3 0.3 2.2
Bearing holder (LCD, XCC and XCD types only) M100 x 2.0 191 19.5 141
Impeller housing bolt M8 x 1.25 19.7 2.0 14
64 mm lock nut M64 x 1.5 123 12.5 90
Pinion gear nut M18 x 1.0 142 14.5 105
• EXTENSION CASE/MOUNTING CASE
Extension case bolt M10 x 1.25 39 4.0 29
Lower rubber mounting bolt M12 x 1.25 83 8.5 61
Upper rubber mounting bolt M12 x 1.25 83 8.5 61
*1: If the split pin cannot be set by tightening the 18 mm castle nuts to 1 N
.
m (0.1 kgf
.
m, 0.7 lbf
.
ft), tighten the 18 mm
castle nut until the split pin can be set. Note that the maximum torque of the 18 mm castle nut is 44 N
.
m (4.5 kgf
.
m,
33 lbf
.
ft).
To Next Page
