HP 5920 Series - Page 43

257 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

36

[Sysname] vlan 30

[Sysname-vlan30] fcoe enable vsan 1

[Sysname-vlan30] quit

NOTE:

The access VSAN of FC 1/0/2 is VSAN 1 (the default). For the FC interface to perform VSAN mode

negotiation, this VSAN must be mapped to a VLAN enabled with FCoE.

Table of Contents

Configuration Guide1
Table of Contents3
FC and Fcoe Overview8
- Storage Area Network8
- Fc San8
- FC Protocol9
- Fcoe12
  - Basic Concepts13
  - How Fcoe Works14
- Fcoe Modes16
- Protocols and Standards19
FC and Fcoe Configuration Guidelines20
- Configuring the Switch to Operate in Advanced Mode or Expert Mode20
- Configuring an Fcoe Mode20
- FC and Fcoe Features Supported in Different Fcoe Modes20
Configuring FC Interfaces22
- Changing the Port Type between a Layer 2 Ethernet Interface and an FC Interface22
- Configuring an FC Interface22
- Displaying and Maintaining FC Interfaces23
Configuring VFC Interfaces24
- Configuring a VFC Interface24
- Displaying and Maintaining VFC Interfaces25
Configuring FC Link Aggregation26
- Overview26
- Basic Concepts26
  - FC Aggregation Group, Member Interface, and FC Aggregate Interface26
  - Member Interface Status26
- How FC Link Aggregation Works26
- FC Link Aggregation Networking Guidelines28
- FC Link Aggregation Configuration Task List29
- Configuring an FC Aggregate Interface29
- Assigning an FC Interface to an FC Aggregation Group30
- Enabling Local-First Load Sharing31
- Displaying and Maintaining FC Link Aggregation31
- FC Link Aggregation Configuration Example32
Enabling Fcoe35
- Fcoe Enabling Configuration Task List35
- Enabling Fcoe for a VLAN and Mapping the VLAN to a VSAN35
  - Configuration Restrictions and Guidelines35
  - Configuration Procedure36
- Configuring an FC-MAP Value36
- Configuring an FKA Advertisement Interval Value36
- Configuring the FCF Priority38
  - Configuring the System FCF Priority38
  - Configuring the VFC Interface FCF Priority38
- Displaying and Maintaining Fcoe38
- Fcoe Enabling Configuration Example39
  - Network Requirements39
  - Configuration Procedure39
Configuring Vsans44
- VSAN Fundamentals44
- Creating a VSAN48
- Configuring the Trunk Mode48
- Configuring an Access VSAN49
  - Assigning an Interface to a VSAN as an Access Port49
  - Assigning Interfaces to a VSAN as Access Ports in Bulk49
- Configuring a Trunk VSAN50
- Displaying and Maintaining Vsans50
- VSAN Configuration Examples50
  - VSAN Configuration Example by Using FC Interfaces50
  - VSAN Configuration Examples by Using VFC Interfaces53
Building a Fabric57
- Overview57
- Fabric Building Configuration Task List59
  - Building a Fabric Statically60
  - Building a Fabric Dynamically60
- Enabling or Disabling the Fabric Configuration Feature61
- Setting a Fabric Name61
- Setting the Switch Priority61
- Configuring an Allowed Domain ID List62
- Configuring a Domain ID for a Switch63
- Binding the WWN of an N_Port to an FC Address63
- Configuring Fabric Timers64
  - Configuring Fabric Timers in System View64
  - Configuring Fabric Timers in VSAN View64
- Configuring Fabric Reconfiguration65
  - Enabling the Automatic Reconfiguration Feature65
  - Manually Initiating a Fabric Reconfiguration65
- Configuring an FC Interface to Reject Incoming RCF Requests66
- Enabling SNMP Notifications66
- Configuring RSCN Aggregation66
- Configuring and Obtaining FC4 Information of Nodes67
  - Enabling SCSI-FCP Information Autodiscovery68
  - Configuring the Default FC4 Information for a Node68
- Displaying and Maintaining a Fabric69
- Fabric Building Configuration Examples69
  - Static Fabric Building Configuration Example69
  - Dynamic Fabric Building Configuration Example72
Configuring FC Routing and Forwarding77
- Overview77
- Configuring Static FC Routes80
  - Configuration Restrictions and Guidelines80
  - Configuration Procedure81
- Configuring FSPF81
- Displaying and Maintaining FC Routing and Forwarding85
- FC Routing Configuration Examples86
Configuring FC Zones104
- Overview104
- FC Zone Configuration Task List113
- Configuring a Zoning Mode114
- Configuring the Pairwise Feature115
- Configuring Zone Aliases115
- Configuring Zones116
- Configuring Zone Sets116
- Configuring the Default Zone Policy117
- Configuring the Zone Distribution and Merge Type117
- Configuring a Merge Control Mode117
- Enabling Hard Zoning118
- Activating a Zone Set and Distributing It to the Entire Fabric119
- Triggering a Complete Distribution119
- Renaming Zone Aliases, Zones, and Zone Sets120
- Copying Zone Aliases, Zones, and Zone Sets120
- Deleting the Zone Database121
- Enabling SNMP Notifications121
- Displaying and Maintaining FC Zones121
- FC Zone Configuration Example122
Configuring NPV127
- Overview127
- NPV Configuration Task List128
- Configuring Uplink Interfaces and Downlink Interfaces129
  - Configuring Uplink Interfaces129
  - Configuring Downlink Interfaces129
- Configuring Downlink-To-Uplink Interface Mappings130
- Initiating a Disruptive Load-Balancing Process130
- Displaying and Maintaining NPV130
- NPV Configuration Examples131
  - NPV Configuration Example by Using FC Interfaces131
  - NPV Configuration Example by Using VFC Interfaces134
Configuring FIP Snooping139
- Overview139
  - FIP Snooping Network Diagram139
  - How FIP Snooping Works140
- FIP Snooping Configuration Task List141
- Enabling FIP Snooping141
- Configuring the Operating Mode of an Ethernet Interface141
- Configuring the FC-MAP Value142
- Displaying and Maintaining FIP Snooping142
- FIP Snooping Configuration Example143
Configuring FCS147
- Overview147
- Starting a Topology Discovery149
- Stopping a Topology Discovery150
- Displaying and Maintaining FCS150
- FCS Configuration Example150
Configuring FDMI154
- Overview154
- Displaying and Maintaining FDMI155
Configuring FC Ping157
- Overview157
- Configuration Procedure157
- FC Ping Configuration Examples157
  - FC Ping Configuration Example by Using FC Interfaces157
  - FC Ping Configuration Examples by Using VFC Interfaces160
Configuring FC Tracert164
- Overview164
- Configuration Procedure165
- FC Tracert Configuration Examples165
  - FC Tracert Configuration Example by Using FC Interfaces165
  - FC Tracert Configuration Example by Using VFC Interfaces170
Comprehensive FC and Fcoe Configuration Examples175
- Fcoe Configuration Example by Using VFC Interfaces (in Standalone Mode)175
- Fcoe Configuration Example by Using VFC Interfaces (in IRF Mode)187
- FC and Fcoe Configuration Example by Using FC Interfaces and VFC Interfaces (in Standalone Mode)205
- FC and Fcoe Configuration Example by Using FC Interfaces and VFC Interfaces (in IRF Mode)217
Appendixes235
- Appendix A Fabric Address Assignment235
- Appendix B Well-Known Fabric Addresses235
Support and Other Resources237
- Contacting HP237
  - Subscription Service237
- Related Information237
  - Documents237
  - Websites237
- Conventions238
Index240

Other manuals for HP 5920 Series

Command Reference607 pages

Configuration Guide424 pages

Fundamentals Configuration Guide215 pages

Installation Guide63 pages

Troubleshooting Guide52 pages

Compliance And Safety Manual58 pages

Related product manuals

Preview: HP 5920

Preview: HP HPE FlexFabric 5930

HP HPE FlexFabric 5930

Preview: HP HPE FlexFabric 5901 Series

HP HPE FlexFabric 5901 Series

Preview: HP 5300

Preview: HP 5120 series

Preview: HP 5400zl Series

HP 5400zl Series

Preview: HP 5130 EI series

HP 5130 EI series

Preview: HP 5500 EI series

HP 5500 EI series

Preview: HP 5120 SI Series

HP 5120 SI Series

Preview: HP FlexFabric 5700

HP FlexFabric 5700

HP ProCurve 5412ZL