HP Codemaster 100 - Page 269

Index
Index-5
adjusting, 5-8
quick pacer functionality test, 13-5
R
rate button
using, 8-3
READY indicator, 13-14
receiving devices, 10-2
recharging time of battery, 1-24
reconditioning battery, 13-15
record
on Alarms, 2-12, 5-11
on Charge, 2-12, 5-11, 10-3, 10-7
on Mark, 2-12, 5-11, 10-3, 10-7
on Shock, 2-12, 5-11, 10-3, 10-7
recorder
automatic recordings, 5-11
bandwidth, 2-12, 10-3, 10-4
cleaning printhead, 13-8
delay, 2-12, 2-13, 10-3
errors, 5-13
opening door, 13-7
operating controls, 1-9
output, 5-10
paper, loading, 13-7
post shock data, 5-12
specifications, 14-5
recording, 5-10 to 5-13
ECG, 6-8
report format
changing, 6-21
report formats, 2-17
resetting selected energy level, 3-4
RESTORE FACTORY SETTINGS, 2-8, 2-9
reviewing Event Summary, 4-17
reviewing ID, 6-15
rhythm leads
Auto ECG, 2-17
RJ11 connection, 10-7
routine testing, 13-1
R-wave detection, 1-20, 4-5, 7-1
S
safety, 6-6
SaO
2
,9-1
selecting energy, 3-1
selecting the ECG source for monitoring, 5-8
semi-automatic external defibrillation, 4-1, 6-1, 11-1
service manual, 12-12, 13-6
setup, 2-7 to 2-12
SETUP LOST, 2-7, 12-2
SETUP MENU 1, 2-8, 2-11
SETUP MENU 2, 2-8
setup menus
Advisory mode, 4-20
setup menus, configuring with, 2-12
setup mode, 2-9
setup/diagnostic menu, 2-9
shift checks, 13-1
shock buttons
defibrillating with, during pacing, 8-7
defibrillating with, using external adhesive pads, 3-8
defibrillating with, using paddles, 3-4
disarming defibrillator, 1-21
performing synchronized cardioversion, using exter-
nal adhesive pads, 7-7
performing synchronized cardioversion, using
paddles, 7-5
testing, 13-3 to 13-4
shock hazard, v, 6-6
shocking the patient, 3-4
shocking, problems with, 12-4
shutdown warning, 1-20, 4-5
sounds (audible indicators), 1-20, 4-5
specifications, 14-1 to 14-10
ECG to paper, 12-16
SpO
2
alarms, 9-10
circulation at application site, 9-7
compared to SaO
2
,9-1
connecting sensor, 9-7
determining which sensor to use, 9-4
inspecting application site, 9-6
monitoring, xii, 9-1
patient movement, effects of, 9-6
preparing the sensor, 9-4
readings, 9-9
recorder output, 9-10
sensor, application troubleshooting, 9-6
sensor, applying, 9-5
types of sensors, 9-3
SpO
2
alarm button, 9-10
SPO2 CABLE OFF, 12-6
SPO2 FAILURE, 12-6
SPO2 LIGHT INTERF, 12-6
SPO2 LOW SIGNAL, 12-7
SPO2 NOISY SIGNAL, 12-6
SPO2 SENSOR FAIL, 12-6
START indicator, 13-14, 13-15
start/stop button
using, 8-4
steam sterilization
monitoring leads, 13-9
paddles, 13-9
Stop key, 6-4
STOP PACER, 12-5
surfaces, cleaning, 13-9
symbol definitions, xvii
sync mode, 1-6
synchronized cardioversion
delivering shock, 7-5
monitoring with external ECG monitor, 7-2