EasyManuals Logo

HP ProCurve 2910al Switch User Manual

HP ProCurve 2910al Switch
126 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #42 background imageLoading...
Page #42 background image
Multimedia Traffic Control with IP Multicast (IGMP)
How IGMP Operates
Configuring Delayed Group Flush
When enabled, this feature continues to filter IGMP groups for a specified
additional period of time after IGMP leaves have been sent. The delay in
flushing the group filter prevents unregistered traffic from being forwarded
by the server during the delay period. In practice, this is rarely necessary on
the switches covered in this guide, which support data-driven IGMP. (Data-
Driven IGMP, which is enabled by default, prunes off any unregistered IGMP
streams detected on the switch.)
Syntax: igmp delayed-flush < time-period >
Where leaves have been sent for IGMP groups, enables the switch
to continue to flush the groups for a specified period of time.
This command is applied globally to all IGMP-configured
VLANs on the switch. Range: 0 - 255; Default: Disabled (0).
Syntax: show igmp delayed-flush
Displays the current igmp delayed-flush setting.
IGMP Proxy Forwarding
Note For more information about PIM-DM and PIM-SM, see the chapters “PIM-DM
(Dense Mode)” and “PIM-SM (Sparse Mode)” in this guide.
When a network has a border router connecting a PIM-SM domain to a PIM-DM
domain, the routers that are completely within the PIM-DM domain have no
way to discover multicast flows in the PIM-SM domain. When an IGMP join
occurs on a router entirely within the PIM-DM domain for a flow that origi-
nates within the PIM-SM domain, it is never forwarded to the PIM-SM domain.
The IGMP proxy is a way to propagate IGMP joins across router boundaries.
The proxy triggers the boundary router connected to a PIM-SM domain to
query for multicast flows and forward them to the PIM-DM domain. IGMP
needs to be configured on all VLAN interfaces on which the proxy is to be
forwarded or received and PIM-DM must be running for the traffic to be
forwarded.
You can configure an IGMP proxy on a selected VLAN that will forward IP
joins (reports) and IGMP leaves to the upstream border router between the
two multicast domains. You must specify the VLANs on which the proxy is
enabled as well as the address of the border router to which the joins are
forwarded.
2-18

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ProCurve 2910al Switch and is the answer not in the manual?

HP ProCurve 2910al Switch Specifications

General IconGeneral
ModelHP ProCurve 2910al Switch
LayerLayer 3
Jumbo Frame SupportYes
Power DeviceInternal power supply
VLAN SupportYes
Power Supply100-240 VAC, 50/60 Hz
Ports24 or 48 x 10/100/1000 ports
Uplink Ports4 x SFP (mini-GBIC)
StackingYes
MAC Address Table Size32000 entries
Routing ProtocolRIP, OSPF, BGP, IGMP
Remote Management ProtocolSNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, TFTP
FeaturesVLAN, QoS, IPv6, ACLs
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af
Operating Temperature0 to 45°C
Operating Humidity15% to 95% (noncondensing)
Power over Ethernet (PoE)PoE+ (802.3at) on PoE+ models, PoE (802.3af) on PoE models

Related product manuals