HP ProLiant DL20 Gen10 - Initial Server Installation

To Next Page

To Previous Page

Initial Initial serverserver installation installation

Depending on the technical expertise of the user and the complexity of the product, for the initial server installation, the user can

choose to:

Order the HPE Installation Service.

Perform the initial server setup procedure.

Initial server installation 47

Main Page

Table of Contents3
Component Identification8
Front Panel Components9
Serial Number/Ilo Information Pull Tab11
Front Panel Leds and Buttons12
Server UID LED13
UID Button Functionality14
Front Panel LED Power Fault Codes15
Rear Panel Components16
Rear Panel Leds17
System Board Components18
System Maintenance Switch Descriptions20
DIMM Slot Locations21
DIMM Label Identification22
Pcie Riser Slot Definitions24
Drive LED Definitions25
Low-Profile LFF Drive LED Definitions26
Smart Carrier (SC) Drive LED Definitions27
Drive Bay Numbering28
Fan Bay Numbering29
Fan Mode Behavior30
Operations31
Power up the Server32
Power down the Server33
Remove the Front Bezel34
Extend the Server from the Rack35
Remove the Server from the Rack37
Install the Server into the Rack38
Remove the Access Panel42
Install the Access Panel43
Remove the Riser Cage44
Install the Riser Cage45
Setup46
Initial Server Installation47
HPE Installation Service48
Setting up the Server49
Operational Requirements52
Space and Airflow Requirements53
Temperature Requirements54
Power Requirements55
Electrical Grounding Requirements56
Rack Warnings and Cautions57
Server Warnings and Cautions59
Electrostatic Discharge60
POST Screen Options61
Hardware Options Installation62
Introduction63
Rack Rail Option64
Installing the Rack Rail Option65
Installing the Rack Rail Hook-And-Loop Strap68
Installing the Front Bezel Option69
Drive Options70
Drive Installation Guidelines71
Drive Support Information72
Installing an LFF Non-Hot-Plug Drive73
Installing an LFF Hot-Plug Drive76
Installing an SFF Hot-Plug Drive77
Power Supply Options78
Hot-Plug Power Supply Calculations79
Power Supply Warnings and Cautions80
Installing a Redundant AC Power Supply81
Installing a Hot-Plug DC Power Supply82
Optical Drive Option89
Installing an Optical Drive in an LFF Chassis90
Installing an Optical Drive in an SFF Chassis93
Installing the Two-Bay SFF Drive Cage Option97
Memory Options99
DIMM Population Information100
Installing a DIMM101
M.2 Ssd/Dedicated Ilo/Serial Port Enablement Option103
M.2 Ssd/Dedicated Ilo/Serial Port Enablement Option Components104
M.2 SSD Standoffs in the System Board105
Installing the M.2 Ssd/Dedicated Ilo/Serial Port Enablement Board106
Installing the Serial Port Cable110
Enabling the Dedicated Ilo Management Module112
M.2 SSD Option113
Installing the M.2 Nvme SSD on the System Board114
Installing an M.2 Nvme SSD on the M.2 Ssd/Dedicated Ilo/Serial Port Enablement Board118
M.2 SATA SSD Enablement Option121
Installing an M.2 SATA SSD122
Storage Controller Options125
Installing a Modular Smart Array Controller Option (Type-A, AROC)126
Installing a Smart Array Standup Storage Controller128
Configuring an HPE Smart Array Gen10 Controller132
Energy Pack Option133
HPE Smart Storage Battery134
Installing an Energy Pack135
Expansion Card Options137
Pcie Expansion Slot Population Rules138
Installing an Expansion Board139
Installing the Flexiblelom Adapter142
Transceiver Option144
Transceiver Warnings and Cautions145
Installing a Transceiver146
Chassis Intrusion Detection Switch Option147
Installing the Chassis Intrusion Detection Switch148
HPE Trusted Platform Module 2.0 Gen10 Option149
Overview150
HPE Trusted Platform Module 2.0 Guidelines151
Installing and Enabling the HPE TPM 2.0 Gen10 Option152
Installing the Trusted Platform Module Board153
Preparing the Server for Installation154
Installing the TPM Board and Cover155
Preparing the Server for Operation157
Enabling the Trusted Platform Module158
Enabling the Trusted Platform Module as TPM 2.0159
Retaining the Bitlocker Recovery Key/Password161
Cabling162
Cabling Guidelines163
Storage Cabling165
Non-Hot-Plug Drive Cabling166
Hot-Plug Drive Cabling169
Two-Bay LFF Hot-Plug Drive Cabling170
Four Bay SFF Hot-Plug Drive Cabling173
4+2 Bay SFF Hot-Plug Drive Cabling174
SATA SSD Cabling177
Energy Pack Cabling179
Controller Backup Power Cabling180
Optical Drive Cabling181
Fan Cabling183
Chassis Intrusion Detection Switch Cabling184
Serial Port Cabling185
Power Supply Cabling186
Software and Configuration Utilities188
Server Mode189
Product Quickspecs190
Active Health System Viewer191
Active Health System192
Active Health System Data Collection193
Active Health System Log194
HPE Ilo 5195
Ilo Federation196
Ilo Restful API197
Restful Interface Tool198
Ilo Amplifier Pack199
Integrated Management Log200
Intelligent Provisioning201
Intelligent Provisioning Operation202
Management Security203
Scripting Toolkit for Windows and Linux204
UEFI System Utilities205
Selecting the Boot Mode206
Secure Boot207
Launching the Embedded UEFI Shell208
HPE Smart Storage Administrator209
HPE Infosight for Servers210
USB Support211
External USB Functionality212
Redundant ROM Support213
Safety and Security Benefits214
Keeping the System Current215
Updating Firmware or System ROM216
Service Pack for Proliant217
Introduction to Smart Update Manager218
Integrated Smart Update Tools219
Updating Firmware from the System Utilities220
Updating the Firmware from the UEFI Embedded Shell221
Online Flash Components222
Drivers223
Software and Firmware224
Operating System Version Support225
HPE Pointnext Portfolio226
Proactive Notifications227
Troubleshooting228
NMI Functionality229
Troubleshooting Resources230
System Battery Replacement231
System Battery Information232
Removing and Replacing the System Battery233
Safety, Warranty, and Regulatory Information235
Regulatory Information236
Notices for Eurasian Economic Union237
Turkey Rohs Material Content Declaration238
Ukraine Rohs Material Content Declaration239
GS Gloss Declaration240
Warranty Information241
Specifications242
Environmental Specifications243
Mechanical Specifications244
Power Supply Specifications245
ATX 290 W Non-Hot-Plug Power Supply (92% Efficiency)246
ATX 290 W Platinum Non-Hot-Plug Power Supply (94% Efficiency)247
HPE 500 W Flex Slot Platinum Hot-Plug Low Halogen Power Supply248
HPE 800W Flex Slot -48VDC Hot Plug Low Halogen Power Supply249
Websites250
Support and Other Resources251
Accessing Hewlett Packard Enterprise Support252
Clearcare Technical Support253
Accessing Updates254
Customer Self Repair255
Remote Support256
Documentation Feedback257

HP ProLiant DL20 Gen10 - Initial Server Installation

Table of Contents

Related product manuals