ISCO 4230 - Page 70

4230 Flow Meter
Section 2 Programming
2-44
Figure 2-4 YSI 600 Sonde Calibration Flow Chart
Program Step #3, “A djust Level/Parameters”
Parameter To Adjust
None - Le vel-YSI 600 - Ph - D.o.
YS I 600 Parameter To Calibrate None - Ph - Con ductivity - D.o.
YS I 600 Ph Calibration
pH4 & pH7 - pH7 & pH 10 - pH4, pH7, & pH10
Rinse probe and place in ph 4.0 solution
Press Enter when stable:
X.XX
pH
Calib rating...
Please Wa it...
Error/warning Override
Yes - No
Rinse probe and place in ph 7.0 solution
Press Enter when ready:
X. XX
pH
Calib rating...
Please Wa it...
Er ro r/warn in g Ove rrid e
Yes - No
Rinse Probe And Place In Ph 7.0 Solution
Press En ter when stable:
X. XX
pH
Calib rating...
Ple ase Wa it...
Error/warning Override
Yes - No
Rinse probe and place in ph 10.0 solution
Press Enter when stable:
X.XX
pH
Err or/warning Override
Yes - No
Rinse probe and place in ph 4.0 solution
Press Enter when stable:
X.XX
pH
Er ro r/war nin g o ve rrid e
Yes - No
Rinse probe and place in ph 7.0 solution
Press En ter when stable:
X. XX
pH
Error/warn in g override
Yes - No
Rinse probe and place in ph 10.0 solution
Press
En t er w h e n s t a b le :
X.XX
pH
Error/ wa rn ing o ve rride
Yes - No
No
Yes
No
Yes
Good Ca librat ion
E rro r/
Wa r n i n g
Erro r
/
Wa r n i n g
Er ro r/ Wa rn i n g Erro r/ Wa r n i n g
Erro r/ Wa r n i n g Erro r / Wa r n
in g
E rro r/ Wa rn i n g
Good Cali
brat ion
Good Cali bration
Good Cal ibrat ion
Good Cal ibrat ion
Good Cali brat ion
Good Cal ibrat ion
No No
No
No
No
Yes
Yes
Yes
Yes
Yes
Calib rating...
Please Wa it...
Calib rating...
Please wait...
Calibrating ...
Please wait...
Ca librat ing ...
Ple ase wait...
YS I 600 Parameter To Calibrate
Non e - Ph - Con ductivity - D.o.
YS I 600 D.O. Calibration
D.O. Standard - Abs. Barometric Pressure - Altitude
Place Prob e in
X.XX
Mg/l solution
Press Enter when ready:
Error/warning Override
Yes - No
Units for altitude entry
Ft. - M
Er ror/warning override
Yes - No
Enter conductivit y calibr atio n units
mS/cm - ppt
Error/warning Override
Yes - No
No
Yes
No Yes
Good Cali brat ion
Erro r/ Wa r n i n g
Er ro r/ Wa r n i n g
Erro r/ Wa r n i n g
Good Cali
brat ion
Good Calib ration
No
Yes
D.O. St an d ard
X.XX
Mg / l
Ab s . Ba ro m e t r ic Pr e ss ure
X.XX
mmHg
Place pro be in calib rat ion cup
Press En ter when ready:
Error/warning Override
Yes - No
No
YesGood Calib ration
Erro r/ Wa r n i n g
Place probe in calib ration cup
Press En te r wh en read y:
En t er con d u ct ivity standard
X XX Un it s
Place probe in
XXX
units solution
Press Enter when ready
Calib rating...
Press Enter when stable
X.XX
Mg / l
Calibrating ...
Press Enter when stable
X. XX
Mg / l
Calibrating...
Press Enter when stable
X.XX
mS /cm
Ca librat ing ...
Press En ter when stable
X.XX
Mg / l