Krone EasyCut F 320 - Page 4

Contents
4 Original Operating Instructions 150000802_00_en
7.3 Checking/setting parallel lifting .................................................................................................. 39
7.4 Connecting hydraulic hoses....................................................................................................... 40
7.5 Installing universal shaft ............................................................................................................ 40
7.6 Checking front end dimension ................................................................................................... 41
7.7 Basic setting of mower............................................................................................................... 42
8 Operation.................................................................................................................................. 43
8.1 Safety device front ..................................................................................................................... 43
8.1.1 Folding up front safety device.................................................................................................... 43
8.1.2 Folding down safety device front ............................................................................................... 44
8.2 Side guard - for the “series” version .......................................................................................... 45
8.2.1 Folding down side guard (working position) .............................................................................. 45
8.2.2 Folding up side guard (transport position) ................................................................................. 45
8.3 Support jack............................................................................................................................... 46
8.3.1 Inserting support jack (transport position).................................................................................. 46
8.3.2 Lowering support jack (parking position) ................................................................................... 46
8.4 Lowering machine from transport position to working position .................................................. 46
8.5 Raising machine from working position to transport position..................................................... 46
8.6 Mowing....................................................................................................................................... 47
9 Driving and Transport ............................................................................................................. 48
9.1 Preparing machine for road travel ............................................................................................. 49
9.2 Switching off the machine.......................................................................................................... 50
10 Settings..................................................................................................................................... 51
10.1 Setting the cutting height ........................................................................................................... 51
10.2 Increasing/reducing ground pressure ........................................................................................ 52
10.3 Setting high-cut skids................................................................................................................. 52
11 Maintenance - General Information........................................................................................ 53
11.1 Maintenance table ..................................................................................................................... 53
11.1.1 Maintenance - Once after 50 hours ........................................................................................... 53
11.1.2 Maintenance - Before the beginning of the season ................................................................... 53
11.1.3 Maintenance - Every 10 hours, but at least once a day............................................................. 54
11.1.4 Maintenance - Every 50 hours................................................................................................... 54
11.1.5 Maintenance - Every 200 hours................................................................................................. 54
11.2 Tightening torques ..................................................................................................................... 55
11.3 Deviating tightening torques ...................................................................................................... 58
11.4 Venting the friction clutch........................................................................................................... 58
11.5 Checking/replacing guard cloths................................................................................................ 59
12 Maintenance - Hydraulic System............................................................................................ 60
13 Maintenance - Gearbox ........................................................................................................... 61
13.1 Main gearbox ............................................................................................................................. 61
13.2 Mower gearbox .......................................................................................................................... 62
13.3 Oil change and oil level check on the cutterbar ......................................................................... 63
14 Maintenance - Cutterbar.......................................................................................................... 65
14.1 Rotary hub ................................................................................................................................. 65
14.2 Replacing shear protection on rotary hub.................................................................................. 66
14.3 Checking/changing blades......................................................................................................... 67
14.3.1 Checking blades for wear .......................................................................................................... 67
14.3.2 Changing blades for the “blade screw connection” version ....................................................... 68
14.3.3 Changing blades for the “blade quick fastener” version ............................................................ 69
14.4 Checking/replacing retaining bolts............................................................................................. 70
14.5 Checking/replacing blade carrier ............................................................................................... 70
14.6 Checking/replacing cutting discs/mower drums......................................................................... 71
14.6.1 Checking the wear limit on cutting discs/mower drums ............................................................. 72
14.7 Checking/replacing linings on cutterbar..................................................................................... 72
15 Maintenance - Lubrication ...................................................................................................... 74
15.1 Lubricating universal shaft ......................................................................................................... 74
15.2 Lubrication chart - Machine ....................................................................................................... 75