Krone EasyCut F 320

To Next Page

To Previous Page

16 Storage

78 Original Operating Instructions 150000802_00_en

INFORMATION

Write down all repair jobs which must be performed by the next harvest and arrange for them

to be done with sufficient lead time. Your KRONE dealer is better able to perform

maintenance service and any required repairs outside of harvest season.

Main Page

Default Chapter3
- Table of Contents3
1 Information on this Document6
- Validity6
- Re-Ordering6
- Applicable Documents6
- Target Group of this Document6
- How to Use this Document6
- Directories and References6
- Figures7
- Information on Direction7
- Conversion Table9
2 Safety12
- Intended Use12
- Service Life of the Machine12
- Basic Safety Instructions12
- Importance of Operating Instructions12
- Staff Qualification13
- Children in Danger13
- Connecting the Machine13
- Structural Modifications on the Machine13
- Additional Equipment and Spare Parts14
- Jobs on the Machine14
- Operational Safety: Technically Sound Condition14
- Danger Zones15
- Ensuring Functionality of Safety Devices17
- Personal Protective Equipment17
- Safety Markings on the Machine17
- Road Safety18
- Parking the Machine Safely18
- Consumables19
- Dangers Arising from Environment19
- Sources of Danger on the Machine20
- Dangers in Connection with Certain Activities: Working on the Machine21
- Behaviour in Dangerous Situations and in Case of Accidents22
- Safety Routines23
- Shutting down and Safeguarding the Machine23
- Securing Raised Machine and Machine Parts against Lowering23
- Safely Performing Oil Level Check, Oil Change and Filter Element Change24
- Safety Labels on the Machine24
3 Machine Description30
- Machine Overview30
- Labelling30
- Intermediate Universal Shaft31
4 Technical Data32
- Consumables32
5 Control and Display Elements33
- Hydraulic Control Units of the Tractor33
6 Initial Operation34
- Checklist for Initial Operation34
- Preparing Front Mounted Mower35
- Adapting Coupling Points35
- Adapting Universal Shaft37
7 Start-Up38
- Preparing Tractor38
- Connecting Machine to Tractor38
- Checking/Setting Parallel Lifting39
- Connecting Hydraulic Hoses40
- Installing Universal Shaft40
- Checking Front End Dimension41
- Basic Setting of Mower42
8 Operation43
- Safety Device Front43
- Folding up Front Safety Device43
- Folding down Safety Device Front44
- Side Guard - for the "Series" Version45
- Folding down Side Guard (Working Position)45
- Folding up Side Guard (Transport Position)45
- Support Jack46
- Inserting Support Jack (Transport Position)46
- Lowering Support Jack (Parking Position)46
- Lowering Machine from Transport Position to Working Position46
- Raising Machine from Working Position to Transport Position46
- Mowing47
9 Driving and Transport48
- Preparing Machine for Road Travel49
- Switching off the Machine50
10 Settings51
- Setting the Cutting Height51
- Increasing/Reducing Ground Pressure52
- Setting High-Cut Skids52
11 Maintenance - General Information53
- Maintenance Table53
- Maintenance - Once after 50 Hours53
- Maintenance - before the Beginning of the Season53
- Maintenance - Every 10 Hours, but at Least Once a Day54
- Maintenance - Every 50 Hours54
- Maintenance - Every 200 Hours54
- Tightening Torques55
- Deviating Tightening Torques58
- Venting the Friction Clutch58
- Checking/Replacing Guard Cloths59
12 Maintenance - Hydraulic System60
13 Maintenance - Gearbox61
- Main Gearbox61
- Mower Gearbox62
- Oil Change and Oil Level Check on the Cutterbar63
14 Maintenance - Cutterbar65
- Rotary Hub65
- Replacing Shear Protection on Rotary Hub66
- Checking/Changing Blades67
- Checking Blades for Wear67
- Changing Blades for the "Blade Screw Connection" Version68
- Changing Blades for the "Blade Quick Fastener" Version69
- Checking/Replacing Retaining Bolts70
- Checking/Replacing Blade Carrier70
- Checking/Replacing Cutting Discs/Mower Drums71
- Checking the Wear Limit on Cutting Discs/Mower Drums72
- Checking/Replacing Linings on Cutterbar72
15 Maintenance - Lubrication74
- Lubricating Universal Shaft74
- Lubrication Chart - Machine75
16 Storage77
17 Waste Disposal79
18 Index80
19 Declaration of Conformity85

Krone EasyCut F 320 - Page 78

Table of Contents

Related product manuals