Krone EasyCut F 320

To Previous Page

Maschinenfabrik

Bernard Krone GmbH & Co. KG

* Heinrich-Krone-Straße 10

D-48480 Spelle

* Postfach 11 63

D-48478 Spelle

' +49 (0) 59 77 / 935-0

6 +49 (0) 59 77 / 935-339

ü www.landmaschinen.krone.de

V.1

Main Page

Default Chapter3
- Table of Contents3
1 Information on this Document6
- Validity6
- Re-Ordering6
- Applicable Documents6
- Target Group of this Document6
- How to Use this Document6
- Directories and References6
- Figures7
- Information on Direction7
- Conversion Table9
2 Safety12
- Intended Use12
- Service Life of the Machine12
- Basic Safety Instructions12
- Importance of Operating Instructions12
- Staff Qualification13
- Children in Danger13
- Connecting the Machine13
- Structural Modifications on the Machine13
- Additional Equipment and Spare Parts14
- Jobs on the Machine14
- Operational Safety: Technically Sound Condition14
- Danger Zones15
- Ensuring Functionality of Safety Devices17
- Personal Protective Equipment17
- Safety Markings on the Machine17
- Road Safety18
- Parking the Machine Safely18
- Consumables19
- Dangers Arising from Environment19
- Sources of Danger on the Machine20
- Dangers in Connection with Certain Activities: Working on the Machine21
- Behaviour in Dangerous Situations and in Case of Accidents22
- Safety Routines23
- Shutting down and Safeguarding the Machine23
- Securing Raised Machine and Machine Parts against Lowering23
- Safely Performing Oil Level Check, Oil Change and Filter Element Change24
- Safety Labels on the Machine24
3 Machine Description30
- Machine Overview30
- Labelling30
- Intermediate Universal Shaft31
4 Technical Data32
- Consumables32
5 Control and Display Elements33
- Hydraulic Control Units of the Tractor33
6 Initial Operation34
- Checklist for Initial Operation34
- Preparing Front Mounted Mower35
- Adapting Coupling Points35
- Adapting Universal Shaft37
7 Start-Up38
- Preparing Tractor38
- Connecting Machine to Tractor38
- Checking/Setting Parallel Lifting39
- Connecting Hydraulic Hoses40
- Installing Universal Shaft40
- Checking Front End Dimension41
- Basic Setting of Mower42
8 Operation43
- Safety Device Front43
- Folding up Front Safety Device43
- Folding down Safety Device Front44
- Side Guard - for the "Series" Version45
- Folding down Side Guard (Working Position)45
- Folding up Side Guard (Transport Position)45
- Support Jack46
- Inserting Support Jack (Transport Position)46
- Lowering Support Jack (Parking Position)46
- Lowering Machine from Transport Position to Working Position46
- Raising Machine from Working Position to Transport Position46
- Mowing47
9 Driving and Transport48
- Preparing Machine for Road Travel49
- Switching off the Machine50
10 Settings51
- Setting the Cutting Height51
- Increasing/Reducing Ground Pressure52
- Setting High-Cut Skids52
11 Maintenance - General Information53
- Maintenance Table53
- Maintenance - Once after 50 Hours53
- Maintenance - before the Beginning of the Season53
- Maintenance - Every 10 Hours, but at Least Once a Day54
- Maintenance - Every 50 Hours54
- Maintenance - Every 200 Hours54
- Tightening Torques55
- Deviating Tightening Torques58
- Venting the Friction Clutch58
- Checking/Replacing Guard Cloths59
12 Maintenance - Hydraulic System60
13 Maintenance - Gearbox61
- Main Gearbox61
- Mower Gearbox62
- Oil Change and Oil Level Check on the Cutterbar63
14 Maintenance - Cutterbar65
- Rotary Hub65
- Replacing Shear Protection on Rotary Hub66
- Checking/Changing Blades67
- Checking Blades for Wear67
- Changing Blades for the "Blade Screw Connection" Version68
- Changing Blades for the "Blade Quick Fastener" Version69
- Checking/Replacing Retaining Bolts70
- Checking/Replacing Blade Carrier70
- Checking/Replacing Cutting Discs/Mower Drums71
- Checking the Wear Limit on Cutting Discs/Mower Drums72
- Checking/Replacing Linings on Cutterbar72
15 Maintenance - Lubrication74
- Lubricating Universal Shaft74
- Lubrication Chart - Machine75
16 Storage77
17 Waste Disposal79
18 Index80
19 Declaration of Conformity85

Krone EasyCut F 320 - Page 86

Table of Contents

Related product manuals