To this Document
10
Pos: 6.1 /Überschri ften/Überschri ften 1/U-Z/Zu diesem Dokumen t @ 107\mod_1334231929021 _78.docx @ 965257 @ 1 @ 1
2 To this Document
Pos: 6.2 /BA/Einlei tung/Gültigkeit/ Rundballenpressen/ Gültigkeit Forti ma F1250-V1800 @ 512\mod_15028 66374096_78.doc x @ 3508316 @ 2 @ 1
2.1 Validity
These operating instructions are valid for round balers of types:
Fortima F 1250 (MC)
Fortima V 1600 (MC)
Fortima V 1500 (MC)
Fortima V 1800 (MC)
Pos: 6.3.1 /Überschr iften/Überschr iften 2/K-O/N/Nachbes tellung (Nachbestel lung dieses Dokuments) @ 349\mod_143635597481 3_78.docx @ 2625865 @ 2 @ 1
2.2 Re-Ordering
Pos: 6.3.2 /BA/Zu diese m Dokument/Nachbeste llung_Text @ 512\mod_15023 74195211_78.doc x @ 3506737 @ @ 1
If this document has become unusable in whole or in part, you can order a replacement, quoting
the document number on the cover sheet. Contact data can be found in the chapter “Contact
persons”.
The document can additionally be downloaded via the KRONE Media Center
http://www.mediathek.krone.de//.
Pos: 6.4 /Überschri ften/Überschri ften 2/K-O/MMitgeltende Dok umente @ 187\mod_1380 113031071_78.docx @ 1609664 @ 2 @ 1
2.3 Further applicable documents
Pos: 6.5 /BA/Zu diesem Dok ument/Mitgeltende Do kumente_Einführung ssatz_alle Maschine n @ 187\mod_138011394 0483_78.docx @ 1609940 @ @ 1
To ensure that the machine is used safely and as intended, observe the following further
applicable documents:
Pos: 6.6 /BA/Zu diesem Dok ument/Mitgeltende Do kumente_Fortima @ 338\ mod_1430728201420_7 8.docx @ 2564065 @ @ 1
Part designation Document type
Universal shaft Operating instructions
Operation terminal Beta Operating instructions
CCI terminal (optional) Operating instructions
WTK joystick (optional) Operating instructions
Pos: 6.7 /Überschri ften/Überschri ften 2/U-Z/ZZielgruppe di eses Dokuments @ 187\mod_1 380113123454_78.d ocx @ 1609723 @ 2 @ 1
2.4 Target group of this document
Pos: 6.8 /BA/Zu diesem Dok umentZielgruppe @ 345\ mod_1434348246902_78. docx @ 2606935 @ @ 1
This document aims at the operators of the machine fulfilling the minimum requirements of
personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.
Pos: 6.9.1 /Überschr iften/Überschr iften 2/P-T/SSo benutzen Si e dieses Dokument @ 188\mod_ 1380548350021_78. docx @ 1614365 @ 2 @ 1
2.5 How to use this document
Pos: 6.9.2 /Überschr iften/Überschr iften 3/U-Z/Verzeic hnisse und Verweise @ 336\mod _1429854437094_78.doc x @ 2556421 @ 3 @ 1
2.5.1 Directories and References
Pos: 6.9.3 /BA/Zu diese m Dokument/So benutzen Si e dieses Dokument_Ver zeichnisse und Verweis e_Text @ 333\mod_1429085 378408_78.docx @ 2544425 @ @ 1
Table of contents/headers:
The table of contents as well as the headers in this instruction are used for quick navigation in
the chapters.
Index directory:
In the index directory, you can find information on the desired subject via catchwords which are
in alphabetical order. The index directory can be found on the last page of this instruction.
Cross references:
Cross references to another place in the operating instructions or to another document are in
the text and specify the chapter and subchapter or section. The designation of subchapters or
sections is presented in quotation marks.
Example:
Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening
Torques”.
The subchapter or the section can be found via an entry in the table of contents and in the index
directory.
Pos: 6.9.4 /Layout Modul e /---------- -----Seitenumbruch- ------------ --- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...
