Lenze EPM-T1 Series - Page 537

Total index
15
Appendix
15.3
L
15.3−5
EDSPM−TXXX−9.0−11/2009
8xdigital output 1A
− Connection, 4.9−2
− Description, 4.9−1
− Features, 4.9−1
− Overview, 4.9−1
− Status display, 4.9−2
− Technical data, 4.9−2
− Terminal assignment, 4.9−2
8xdigital output 2A
− Connection, 4.11−2
− Description, 4.11−1
− Features, 4.11−1
− Overview, 4.11−1
− Status display, 4.11−2
− Technical data, 4.11−2
− Terminal assignment, 4.11−2
8xdigital outputs 0.5A, Properties, 4.7−1
A
Address setting, 4.2−2
Air humidity, 3.1−1
Ambient conditions
− Climatic, 3.1−1
− Mechanical, 3.1−1
Analog inputs, Status request, 8.10−5 , 9.10−5
Analog modules
− 4xanalog input, Parameter setting, 12.3−1
− 4xanalog input / output, Parameter setting, 12.3−4
− 4xanalog output, Parameter setting, 12.3−3
− Conversion of measured values, 12.3−7 , 13.1−6
− transmitting input data, 12.3−7 , 13.1−6
− transmitting output data, 12.3−7 , 13.1−6
Analog outputs, #Status request, 8.10−5 , 9.10−5
Application, as directed, 1.3−1
Application as directed, 1.3−1
Application examples, I/O system IP20 on the
controller 93xx, 11.1−2
Approval, UL, 3.1−1
B
Baud rate
− Setting, 8.5−1 , 9.5−1
− Setting at the CAN Gateway, 4.1−2 , 5.1−3 , 5.2−3 ,
5.3−3 , 5.4−3
C
Cable specification, 7.4−1 , 7.5−2
CAN Gateway
− Baud rate setting, 4.1−2 , 5.1−3 , 5.2−3 , 5.3−3 , 5.4−3
− Setting the node address, 4.1−3 , 5.1−3 , 5.2−3 , 5.3−3
, 5.4−3
CAN gateway
− Description, 4.1−1
− Fault indications, 4.1−3 , 4.2−3
− Overview, 4.1−1
− Properties, 4.1−1
− Status display, 4.1−3 , 4.2−3
− Technical data, 4.1−4
CAN GatewayECO
− Description, 4.2−1
− Overview, 4.2−1
− Properties, 4.2−1
− Technical data, 4.2−4
CANopen
− Connecting, 4.1−1 , 4.2−1 , 5.1−2 , 5.2−2 , 5.3−2 ,
5.4−2
− Connection to the module, Pin assignment, 5.1−2 ,
5.2−2 , 5.3−2 , 5.4−2
− Networking via, 9.1
CE conformity, 1.3−1
COB−ID, 8.1−2 , 9.1−2
CoDeSys, 10.4−1
Commissioning, 11.1
− I/O system IP20 on the controller 93xx, 11.1−2
Communication connection, 7.4−1 , 7.5−3
Communication Object Identifier, 8.1−2 , 9.1−2
Communication phases, 8.2−1 , 9.2−1
Communication, connection, 7.4−1 , 7.5−3
Compact modules, Compatibility, with drive and
automation components, 8.3−9 , 9.3−9
Compact system
− Dimensions, 6.2−1
− Mounting dimensions, 6.2−1
Compatibility
− Compact modules, with drive and automation
components, 8.3−9 , 9.3−9
− Modular system, with drive and automation
components, 8.3−9 , 9.3−9
Configuration, Diagnostics, 10.6−1
Conformity, 1.3−1
− CE, 3.1−1