Link Controls CS 320 - CS Radio; Digital 991

22 – Control CS 320 / Rev.D 1.01 Control CS 320 / Rev.D 1.01 – 23
5.16 CS radio
Connection
 Plug the radio receiver into connector strip X9.Plug the radio receiver into connector strip X9.
Teach transmitter codes
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. The programming mode is activated. 1.6 seconds. The programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Press the channel button of your transmitter. Press the channel button of your transmitter.
If the radio controller has stored the transmitter code, the If the radio controller has stored the transmitter code, the
LED lights up for approx. 4 seconds.LED lights up for approx. 4 seconds.
A total of 15 transmitter codes (hand-held transmitter) can be
taught.
Ifallstoragespacesareoccupied,theLEDashesveryrapidly.
Furthermore, it is possible to integrate additional hand-
held transmitters through duplication from one hand-held
transmitter to the next.
Targeted deletion of a transmitter code
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. The programming mode is activated. 1.6 seconds. The programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Continue to press and hold the programming button. Erase Continue to press and hold the programming button. Erase
modeisactivated.TheLEDashesveryquickly.modeisactivated.TheLEDashesveryquickly.
 Press the desired channel button of your transmitter. Press the desired channel button of your transmitter.
If the LED lights up for approx. 4 seconds, the corresponding If the LED lights up for approx. 4 seconds, the corresponding
transmitter code has been deleted.transmitter code has been deleted.
Youcancancelthedeletionprocessbybrieypressingthe
programming button.
RESET (completely delete memory)
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. Programming mode is activated. 1.6 seconds. Programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Continue to press and hold the programming button. Continue to press and hold the programming button.
Erasemodeisactivated.TheLEDashesveryquickly.Erasemodeisactivated.TheLEDashesveryquickly.
 Press and hold the programming button for longer than Press and hold the programming button for longer than
1.6seconds. 1.6seconds.
If the LED lights up for approx. 4 seconds, all storage spaces If the LED lights up for approx. 4 seconds, all storage spaces
have been deleted.have been deleted.
Youcancancelthedeletionprocessbybrieypressingthe
programming button.
5.17 5.17 Digital 991Digital 991
Connection
 Plug the radio receiver into connector strip X9.Plug the radio receiver into connector strip X9.
Teach transmitter codes
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. The programming mode is activated. 1.6 seconds. The programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Press the teach button and then the channel button of your Press the teach button and then the channel button of your
transmitter. transmitter.
If the radio controller has stored the transmitter code, the If the radio controller has stored the transmitter code, the
LED lights up for approx. 2 seconds.LED lights up for approx. 2 seconds.
A total of max. 200 transmitter codes (hand-held transmitter)
can be taught. If all storage spaces are occupied, the LED
ashesveryrapidly.
Targeted deletion of a transmitter code.
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. The programming mode is activated. 1.6 seconds. The programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Continue to press and hold the programming button. Erase Continue to press and hold the programming button. Erase
modeisactivated.TheLEDashesveryquickly.modeisactivated.TheLEDashesveryquickly.
 Press the desired channel button of your transmitter. Press the desired channel button of your transmitter.
If the LED lights up for approx. 2 seconds, the corresponding If the LED lights up for approx. 2 seconds, the corresponding
transmitter code has been deleted.transmitter code has been deleted.
Youcancancelthedeletionprocessbybrieypressingthe
programming button.
RESET (completely delete memory)
 Press and hold the programming button (B) for longer than Press and hold the programming button (B) for longer than
1.6 seconds. The programming mode is activated. 1.6 seconds. The programming mode is activated.
TheLED(C)ashes.TheLED(C)ashes.
 Continue to press and hold the programming button. Erase Continue to press and hold the programming button. Erase
modeisactivated.TheLEDashesveryquickly.modeisactivated.TheLEDashesveryquickly.
 Press and hold the programming button again for longer Press and hold the programming button again for longer
than 1.6 seconds. If the LED lights up for approx. 2 seconds, than 1.6 seconds. If the LED lights up for approx. 2 seconds,
all storage spaces have been deleted.all storage spaces have been deleted.
Youcancancelthedeletionprocessbybrieypressingthe
programming button.
Installation