Link Controls CS 320 - Setting the Electronic Limit Position System Via the LCD Monitor; Setting the Intermediate Positions of the Electronic Limit Position System Via the LCD Monitor

26 – Control CS 320 / Rev.D 1.01 Control CS 320 / Rev.D 1.01 – 27
EN
7.4 7.4 Setting the electronic limit position Setting the electronic limit position
system via the LCD monitorsystem via the LCD monitor
ATTENTION!
Improper assembly will cause damage or
destruction!
The monitor must be plugged in whilst de-energised. Only
a standard LCD monitor (#91447) from Marantec Legden
may be used.
Change to adjustment mode
 Press the (P) button until ADJUSTMENT appears.Press the (P) button until ADJUSTMENT appears.
Setting the UP end position
 Drive the door to the desired UP end position by pressing Drive the door to the desired UP end position by pressing
the (+/–) buttons.the (+/–) buttons.
 Save end positions by pressing the (P) button and Save end positions by pressing the (P) button and
additionally also the (+) button. additionally also the (+) button.
“STOREUP”appearsinthedisplay. “STOREUP”appearsinthedisplay.
Setting the DOWN end position
 Drive the door to the desired DOWN end position with the Drive the door to the desired DOWN end position with the
(+/–) buttons.(+/–) buttons.
 Save end position by pressing the (P) button and additionally Save end position by pressing the (P) button and additionally
also the (–) button. also the (–) button.
“STOREDOWN”appearsinthedisplay. “STOREDOWN”appearsinthedisplay.
The adjustment mode is automatically exited.
Note
− The adjustment mode is automatically exited after approx.
7 minutes, if no button is pressed.
− Normal operation is not possible until both end positions
have been learned through the initial calibration.
− If an end position is to be corrected, the ADJUSTMENT
mode can be exited by pressing the (P) button after
learning the special end positions.
− After programming the limit switches, the system run-time
islearnedautomatically.ThedisplayshowsTEACHINRUN.
The controller functions are the same as in automatic mode.
7.5 7.5 Setting the intermediate positions of the Setting the intermediate positions of the
electronic limit position system via the electronic limit position system via the
LCD monitorLCD monitor
Drive the door to the desired position in automatic
mode
 Drive the door to the desired intermediate positions Drive the door to the desired intermediate positions
(INTPOSUPorINTPOSDOWN)withthe(+/–)buttons.(INTPOSUPorINTPOSDOWN)withthe(+/–)buttons.
Change to input mode
 Press the (P) button until INPUT appears.Press the (P) button until INPUT appears.
 Press and hold the buttons (+) and (–) simultaneouPress and hold the buttons (+) and (–) simultaneously for
morethan2seconds.Therstparameterappearsinthe
second line of the display.
Save the intermediate UP (INT POS UP) or DOWN
(INTPOS DOWN) position
 Press the buttons (+/–) until the parameter INT POS UP or Press the buttons (+/–) until the parameter INT POS UP or
INT POS DOWN appears. INT POS DOWN appears.
The value stands at A.The value stands at A.
 Press the button (P) to accept the current door position as Press the button (P) to accept the current door position as
the intermediate position.the intermediate position.
 Save the intermediate position by pressing the (P) button Save the intermediate position by pressing the (P) button
again.again.
Exit Input operating mode
 Press and hold the buttons (+) and (–) simultaneously for Press and hold the buttons (+) and (–) simultaneously for
more than 1 second. more than 1 second.
Input is exited.Input is exited.
Change to automatic mode
 Press the (P) button until AUTOMATIC appears.Press the (P) button until AUTOMATIC appears.
Note
If an intermediate position is to be corrected, the taught value
can be changed in the INPUT menu or set to A again, so that
a new teach-in can be started.