MAHA LPS 3000 - Selecting the Setup Language

115 pages

Save Page as PDF

To Next Page

To Previous Page

BA052301-en 47

6.3 Selecting the Setup Language

1 Choose a setup

language.

German and

English are

available.

2 Confirm with

<Next>.

 The InstallShield

Wizard appears.

3 Confirm with

<Next>.

Main Page

Table of Contents3
Safety7
Introduction7
Symbols7
Intended Use7
Safety Instructions for Commissioning7
Safety Instructions for Operation8
Safety Instructions for Servicing9
Danger Zone10
Safety Information about Tires11
Safety Information about the Eddy Current Brake11
Safety Information about Motorcycle Testing11
Safety Information about the Anchoring Device LPS 3000 Truck11
Safety Features12
Accessories12
What to Do in the Event of an Accident13
Description14
General Information14
Technical Data15
Communication Desk15
Roller Sets16
Main Switch19
Remote Control19
Description of the Interface Box21
RPM Module (Standard)23
Environmental Module (Standard)25
OBD Module (Optional)26
Pressure/Temperature Module (Optional)26
Analog Input Module (Optional)27
Analog Output Card (Optional)27
Lambda Broadband Sensor28
Measurement Programs33
Calculation Basis34
Road Load34
Torque35
Extrapolation of the Engine Power with Gasoline Engines36
Extrapolation of the Engine Power with Diesel Engines (Naturally Aspirated or Supercharged)37
Extrapolation of the Engine Power with Turbodiesel Engines38
Calculate Engine Factor Fm39
Extrapolation of Drag Power by 2Nd Coast down Trial40
Wheel Drive Operation41
Installation42
Requirements for the Place of Installation42
Safety Measures42
Heat Balance42
Exhaust Suction System44
Fresh Air Supply for the Test Room45
Transport and Storage45
Installation and Initial Operation45
Software46
System Requirements46
Starting the Setup46
Selecting the Setup Language47
Selecting the Destination Folder48
Selecting the SQL Server48
Selecting the Dyno Type49
Selecting Features49
Installing Drivers50
Finishing the Setup50
Additional Settings under Windows 7 or Higher51
Preparations for Testing53
Switch on the Dyno53
Drive Onto Dyno53
Set Wheelbase (Only 4WD Dynos)53
Fix Vehicle54
Fix Car/Truck55
Fix Motorcycle56
Attach Weight Simulator (Optional)57
Connect the RPM Sensor57
Connect Oil Temperature Probe57
Attach Exhaust Suction System58
Position Cooling Air Fan58
Bring the Vehicle up to Operating Temperature58
Vehicle Ready for Testing58
Program Structure59
General Information59
Tree Model60
Screen Design61
Status Line61
Main Screen63
Button Bar63
Starting the Program64
End Program / Switch off Dyno64
Measurements65
Load Simulation65
Identical Functions65
Constant Traction70
Constant Speed72
Driving Simulation73
Constant Engine RPM75
Standstill75
Measure Engine Power76
Display Last Measurement76
Continuous Measurement77
Discrete Measurement80
Engine Flexibility Test82
Speedometer Check83
Vehicle Speed83
Mileage84
Load Adaption (Optional)85
Coefficient Adaption Based on ECE85
Coefficient Adaption Based on SAE J226486
Lug-Down Test (Option)87
Settings88
Database88
Identical Functions88
Performance Curves91
Time Diagram95
Vehicle Data96
Load Simulation Profile97
Driving Cycle Data99
Vehicle Data100
RPM Setting101
Driving Trial102
Special Settings103
Select Dyno Type104
Units104
Language105
Device / Interfaces105
OBD Settings (Optional)106
Diagnosis / Service107
Dyno Status107
Driver's Aid Setup (Optional)107
Test Driving Cycle108
Edit Profile109
New Profile109
Delete Profile110
Backup/Restore Database110
Backup Database110
Restore Database110
Delete Table111
Delete Database111
Maintenance112
Important Information112

MAHA LPS 3000 - Selecting the Setup Language

Table of Contents

Related product manuals