MD Helicopters 369D - Revision 11

CSP-HMI-3 MD Helicopters, Inc.
MAINTENANCE MANUAL
[ Main Menu ]
[ HMI−3 Book TOC ]
[ Chapter 96 TOC ]
Page 214
Revision 11
96-00-00
The information disclosed herein is proprietary to MD Helicopters, Inc.
Neither this document nor any part hereof may be reproduced or transferred to
other documents or used or disclosed to others for manufacturing or any other
purpose except as specifically authorized in writing by MD Helicopters, Inc.
Copyright © 1999−2016 by MD Helicopters, Inc.
G96-0003-4A
SIDE-FEED MODULE TYPE AMM
20-1
TRACK-TYPE AMM 3600T-1 (POLYVINYL CHLO
RIDE)
TOP-FEED MODULE TYPE AMM
20T-1
BURNDY
MINILOK
MINILOK
NOTE
2
SIDE-FEED
MODULE
BUSSING
(TYP)
BUSSING
(TYP)
TOP-FEED
MODULE
F E D C B
A
F E D C B
A
F E D C B
A
A6SMM20T-1
(ALL RECEPTACLES BUSSED)
A23DMM20T-1
(TWO SETS OF THREE
RECEPTACLES BUSSED)
A32DMM20T-1
(THREE SETS OF TWO RE
CEPTACLES BUSSED)
D
C
B
A
D
C
B
A
A4SMM20-1
(ALL TIERS
BUSSED)
D
C
B
A
D
C
B
A
D
C
B
A
D
C
B
A
A22DMM20-1
(TWO TOP TIERS
BUSSED - TWO
BOTTOM TIERS
BUSSED)
A4DMM20-1
(ALL TIERS
INDIVIDUAL)
MINI
LOK
SCRE
W
UPPER
HALF
BASE
11/16 IN.
INSPECTIO
N HOLE
MINILO
K HYTIP
PCM 22M-HIF3 (AWG 24-22) USE HYTOOL M8ND WITH DIE SET N22PCT-1
PCM 20M-HIF3 (AWG 20) USE HYTOOL M8ND WITH DIE SET N20PCT-2
TYPICAL INSTALLATION OF MINILOK TERMINAL BLOCK MODULES
(REF TB1, TB5 TB7 AND TB502)
TRACK, AM0750T-1 (NOTE) (CADMIUM-PLATED
STEEL)
TYPICAL INSTALLATION OF MODULOK TERMINAL BLOCK MODULES
(REF TB3)
13/64 IN.
TRAC
K
2-TIER
MODULE
AMC-1
CLAMP
4-TIER
MODULE
BUSSING
(TYP)
MODULOK CONTACT TIP
AYH 14-H (AWG 20-14)
USE HYTOOL M8ND WITH
DIE SET N14HCT
HEADLESS
SET SCREW
D
C
B
A
D
C
B
A
D
C
B
A
D
C
B
A
D
C
B
A
D
C
B
A
B
A
B
A
B
A
B
A
A2SM14-1
A2DM14-1 A22DM14-1
A4DM14-1
A4SM14-1
NOTE:
THE FOUR MIDDLE NUMERIC DIGITS
IDENTIFY LENGTH. AMM TRACK COMES IN
36 INCH LENGTHS AND IS CUT TO SIZE; AM
TRACK CAN BE ORDERED IN ANY LENGTH
UP TO 32 INCHES (EG. 0750 = 7.50 INCHES.
BURNDY
AMO750T-1
Figure 203. Identification and Replacement of Terminal Block Modules (Sheet 4 of 4)