Mercury 40 Service Manual

SPECIFICATIONS
Page 1A-8 90-828631R3 MARCH 1999
Propeller Information Charts
Mercury/Mariner 50 (4-Stroke) 2.00:1 Non Bigfoot
Wide Open Throttle rpm : 5500-6000
Recommended Transom Heights : 15”, 20”, 22.5”
Right Hand Rotation Standard
Gear Reduction : 2.00:1
Diameter
Pitch
No. of
Blades
Material
Approx.
Gross Boat
Wgt. (lb)
Approx.
Boat
Length
Speed
Range
(mph)
Propeller
Part Number
10” 19” 3 Alum Up to 800 Up to 14’ 43-51 48-73146A40
10” 17” 3 Alum Up to 900 Up to 15’ 40-46 48-73144A40
10” 16” 3 Steel 800-1000 Up to 15’ 37-43 48-91818A5
10” 16” 3 Alum 800-1000 Up to 15’ 37-43 48-73142A40
10-1/8” 15” 3 Steel 900-1300 13-15’ 34-41 48-76232A5
10-1/8” 15” 3 Alum 900-1300 13-15’ 34-41 48-73140A40
10-3/8” 14” 3 Alum 1000-1500 14-16’ 32-37 48-816706A40
10-1/4” 14” 3 Steel 1000-1500 14-16’ 32-37 48-76230A5
10-1/4” 14” 3 Alum 1000-1500 14-16’ 32-37 48-73138A40
10-1/2” 13” 3 Alum 1100-1700 14-17’ 29-34 48-816704A40
10-3/8” 13” 3 Steel 1100-1700 14-17’ 29-34 48-76228A5
10-3/8” 13” 3 Alum 1100-1700 14-17’ 29-34 48-73136A40
10-3/4” 12” 3 Alum 1200-1900 15-17’ 25-31 48-816702A40
10-5/8” 12” 3 Steel 1200-1900 15-17’ 25-31 48-79792A5
10-5/8” 12” 3 Alum 1200-1900 15-17’ 25-31 48-73134A40
10-7/8” 11” 3 Alum 1400-2100 16-18’ 22-27 48-85632A45
11-5/8” 11” 3 Steel 1400-2100 16’ + 22-27 48-823478A5
11-5/8” 10-1/2” 3 Alum 1500-2300 16’ + 20-25 48-827312A10
11-1/4” 10” 3 Alum 1700-2500 17’ + 18-23 48-73132A40
12-1/4” 9” 3 Steel 1900+ 18’ + 13-20 48-97868A10
12-1/4” 9” 3 Alum 1900+ 18’ + 13-20 48-87818A10
12-1/2” 8” 3 Alum 2100+ 18’ + 1-16 48-42738A10
12-1/2” 8” Cup 3 Alum pontoon 48-42738A12

Mercury 40 Specifications

General

Horsepower	40 hp
Starting System	Electric
Steering	Remote
Fuel Induction System	EFI (Electronic Fuel Injection)
Shaft Length	20"
Full Throttle RPM Range	6000