18 – Control CS 310 / Rev.I 1.55 Control CS 310 / Rev.I 1.55 – 19
EN
7.4 7.4 Setting the electronic end position Setting the electronic end position
system using the LCD monitorsystem using the LCD monitor
Damage to property or irreparable damage due to
incorrect installation!
The power supply must be switched off before connecting
the monitor. Only an MFZ monitor may be used.
At plug-in socket X8: LCD Monitor Standard (#91447)
Changing to adjustment mode
Press button (P) until ADJUSTMENT appears.Press button (P) until ADJUSTMENT appears.
Set the OPEN end position
Press the (+/–) buttons to move the door/gate to the Press the (+/–) buttons to move the door/gate to the
desired OPEN end position.desired OPEN end position.
Save the end position setting by pressing button (P) and by Save the end position setting by pressing button (P) and by
additionally pressing the (+) button. additionally pressing the (+) button.
“STORAGE UP” appears in the display. “STORAGE UP” appears in the display.
Set the CLOSED end position
Press the (+/–) buttons to move the door/gate to the Press the (+/–) buttons to move the door/gate to the
desired CLOSED end position.desired CLOSED end position.
Save the end position setting by pressing button (P) and by Save the end position setting by pressing button (P) and by
additionally pressing the (–) button. additionally pressing the (–) button.
“STORAGE DOWN” appears in the display. “STORAGE DOWN” appears in the display.
Adjustment mode is exited automatically.
Please note
− The adjustment mode will end automatically after
approximately 7 seconds if no key is pressed.
− Whencarryingoutadjustmentsforthersttime,itis
necessary to teach-in both end positions. Otherwise, normal
operation not be possible.
− If an end position is corrected, the ADJUSTMENT menu can
be exited by pressing button (P) once the teaching-in of the
special end position has been completed.
− After programming the limit switches, the teach-in of
the system running time is carried out automatically. The
display shows TEACH IN RUN. The functions of the control
are the same as in automatic mode.
7.5 7.5 Setting the intermediate positions of the Setting the intermediate positions of the
electronic end position system using the electronic end position system using the
LCD monitorLCD monitor
In AUTOMATIC mode, move the door/gate to the
desired position
Press the (+/–) button to drive the door to the desired Press the (+/–) button to drive the door to the desired
intermediate position (INC.P.OP or INC.P.CL).intermediate position (INC.P.OP or INC.P.CL).
Changing to Input mode
Press button (P) until INPUT appears.Press button (P) until INPUT appears.
Press buttons (+) and (–) at the same time for lonPress buttons (+) and (–) at the same time for longer than
2seconds.Therstparameterappearsinthesecondlineof
the display.
Saving the intermediate OPEN (INC.P.OP) or CLOSE
(INC.P.CL) position
Press the (+/–) buttons until the parameter INC.P.OP or Press the (+/–) buttons until the parameter INC.P.OP or
INC.P.CL appears. INC.P.CL appears.
The current value is A.The current value is A.
Press button (P) to adopt the current door/gate position as Press button (P) to adopt the current door/gate position as
an intermediate position.an intermediate position.
Save the intermediate position by pressing button (P) again.Save the intermediate position by pressing button (P) again.
Exiting Input mode
Press buttons (+) and (–) at the same time for approx. Press buttons (+) and (–) at the same time for approx.
1seconds. 1seconds.
Input mode is exited.Input mode is exited.
Changing to automatic mode
Press button (P) until AUTOMATIC appears.Press button (P) until AUTOMATIC appears.
Please note
− If an intermediate position requires to be corrected, the
teach-in value can be altered in the INPUT menu or set to A
again to allow a new teach-in procedure to be carried out.
To Next Page
Loading...
Need help?
General
