Mitsubishi FX3U Series Programming Manual

69
FX3G/FX3U/FX3GC/FX3UC Series
Programming Manual - Basic & Applied Instruction Edition
3 Instruction List
3.3 Applied Instructions ... in Ascending Order of FNC Number
1
Introduction
2
Overview
3
Instruction List
4
Devices in Detail
5
Specified the Device & Constant
6
Before Programming
7
Basic Instruction
8
FNC00-FNC09 Program Flow
9
FNC10-FNC19 Move & Compare
10
FNC20-FNC29 Arith. & Logic Operation
Rotation and Shift Operation
30 ROR Rotation Right 3333 ––3 – 3
Section
11.1
31 ROL Rotation Left 3333 ––3 – 3
Section
11.2
32 RCR Rotation Right with Carry – – 33 ––3 – 3
Section
11.3
33 RCL Rotation Left with Carry – – 33 ––3 – 3
Section
11.4
34 SFTR Bit Shift Right 333333333
Section
11.5
35 SFTL Bit Shift Left 333333333
Section
11.6
36 WSFR Word Shift Right 3333––3 – 3
Section
11.7
37 WSFL Word Shift Left 3333––3 – 3
Section
11.8
38 SFWR
Shift write
[FIFO/FILO control]
333333333
Section
11.9
39 SFRD Shift Read [FIFO Control] 333333333
Section
11.10
Data Operation
40 ZRST Zone Reset 333333333
Section
12.1
41 DECO Decode 333333333
Section
12.2
42 ENCO Encode 333333333
Section
12.3
43 SUM Sum of Active Bits 3333––3 – 3
Section
12.4
44 BON Check Specified Bit Status 3333 ––3 – 3
Section
12.5
45 MEAN Mean 3333––3 – 3
Section
12.6
46 ANS Timed Annunciator Set 3333––3 – 3
Section
12.7
47 ANR Annunciator Reset 3333––3 – 3
Section
12.8
48 SQR Square Root – – 33 ––3 – 3
Section
12.9
49 FLT
Conversion to Floating
Point
*6 333 ––3 – 3
Section
12.10
*1: The instruction is provided in the FX 2N /FX 2NC Series Ver. 3.00 or later. *6: The instruction is provided in the FX 3G Series Ver. 1.10 or later.
*2: The function is changed in the FX 3UC Series Ver. 1.30 or later. *7: The instruction is provided in the FX 3U /FX 3UC Series Ver. 2.61 or later.
*3: The instruction is provided in the FX
3UC Series Ver. 1.30 or later. *8: The instruction is provided in the FX 3U /FX 3UC Series Ver. 2.70 or later.
*4: The function is changed in the FX
3UC Series Ver. 2.20 or later. *9: The instruction is provided in the FX 3G Series Ver. 1.40 or later.
*5: The instruction is provided in the FX 3UC Series Ver. 2.20 or later.
FNC No. Mnemonic Symbol Function
FX3G
FX3GC
FX3U
FX3UC
Applicable PLC
Reference
FX1S
FX1N FX2N
FX1NC FX2NC
nDROR
nDROL
nDRCR
nDRCL
n2n1DSSFTR
n2n1DSSFTL
n2n1DS
WSFR
n2n1DSWSFL
n
SFWR
DS
nSFRD DS
D2D1ZRST
n
DECO
DS
n
ENCO
DS
DSSUM
BON D nS
MEAN
D nS
ANS m DS
ANR
DSSQR
DSFLT

Mitsubishi FX3U Series Specifications

General

Model	FX3U Series
Program Memory	64k steps
Execution Speed	0.065 μs/basic instruction
Type	PLC (Programmable Logic Controller)
Power Supply	100-240V AC
I/O Points	Up to 384
Communication	USB
Expansion	Supported via expansion modules
High-Speed Counters	Up to 6 channels
Analog Input/Output	Available via expansion modules
Temperature Range	0 to 55°C
Programming Language	Ladder Logic, Structured Text
Built-in Functions	PID control
Humidity	5 to 95% (non-condensing)