Mitsubishi FX3U Series Programming Manual

70
FX3G/FX3U/FX3GC/FX3UC Series
Programming Manual - Basic & Applied Instruction Edition
3 Instruction List
3.3 Applied Instructions ... in Ascending Order of FNC Number
High-speed Processing
50 REF Refresh 333333333
Section
13.1
51 REFF Refresh and Filter Adjust – – 33 ––3 – 3
Section
13.2
52 MTR Input Matrix 333333333
Section
13.3
53 HSCS High-speed Counter Set 333333333
Section
13.4
54 HSCR High-speed Counter Reset 333333333
Section
13.5
55 HSZ
High-speed Counter Zone
Compare
3333––3 – 3
Section
13.6
56 SPD Speed Detection 333333333
Section
13.7
57 PLSY Pulse Y Output 333333333
Section
13.8
58 PWM Pulse Width Modulation 333333333
Section
13.9
59 PLSR
Acceleration/Deceleration
Setup
333333333
Section
13.10
Handy Instruction
60 IST Initial State 333333333
Section
14.1
61 SER Search a Data Stack 3333 ––3 – 3
Section
14.2
62 ABSD Absolute Drum Sequencer 333333333
Section
14.3
63 INCD
Incremental Drum
Sequencer
333333333
Section
14.4
64 TTMR Teaching Timer – – 33 ––3 – 3
Section
14.5
65 STMR Special Timer – – 33 ––3 – 3
Section
14.6
66 ALT Alternate State 333333333
Section
14.7
67 RAMP Ramp Variable Value 333333333
Section
14.8
68 ROTC Rotary Table Control – – 33 ––3 – 3
Section
14.9
69 SORT SORT Tabulated Data – – 33 ––3 – 3
Section
14.10
*1: The instruction is provided in the FX 2N /FX 2NC Series Ver. 3.00 or later. *6: The instruction is provided in the FX 3G Series Ver. 1.10 or later.
*2: The function is changed in the FX 3UC Series Ver. 1.30 or later. *7: The instruction is provided in the FX 3U /FX 3UC Series Ver. 2.61 or later.
*3: The instruction is provided in the FX
3UC Series Ver. 1.30 or later. *8: The instruction is provided in the FX 3U /FX 3UC Series Ver. 2.70 or later.
*4: The function is changed in the FX
3UC Series Ver. 2.20 or later. *9: The instruction is provided in the FX 3G Series Ver. 1.40 or later.
*5: The instruction is provided in the FX 3UC Series Ver. 2.20 or later.
FNC No. Mnemonic Symbol Function
FX3G
FX3GC
FX3U
FX3UC
Applicable PLC
Reference
FX1S
FX1N FX2N
FX1NC FX2NC
nDREF
nREFF
nMTR D2D1S
HSCS S2 DS1
HSCR S2 DS1
DHSZ SS2S1
SPD S2 DS1
PLSY S2 DS1
PWM S2 DS1
DPLSR S3S2S1
IST D1 D2S
nSER DS2S1
nABSD DS2S1
nINCD DS2S1
nDTTMR
STMR m DS
DALT
n
RAMP
DS2S1
DROTC m2m1S
nSORT Dm2m1S

Mitsubishi FX3U Series Specifications

General

Model	FX3U Series
Program Memory	64k steps
Execution Speed	0.065 μs/basic instruction
Type	PLC (Programmable Logic Controller)
Power Supply	100-240V AC
I/O Points	Up to 384
Communication	USB
Expansion	Supported via expansion modules
High-Speed Counters	Up to 6 channels
Analog Input/Output	Available via expansion modules
Temperature Range	0 to 55°C
Programming Language	Ladder Logic, Structured Text
Built-in Functions	PID control
Humidity	5 to 95% (non-condensing)