NEC Univerge SV8100 - Page 423

UNIVERGE SV8100 Issue 1.0
SV8100 Features and Specifications Manual 2 - 399
20-14-03 Class of Service Options for
DISA/E&M – Trunk Group
Access
This option Enables or Disables a
DISA or tie trunk caller ability to
access trunk groups for outside calls
(Service Code 704).
0 = Off
1 = On
(default = 1 for
COS 1~15)
3
20-14-04 Class of Service Options for
DISA/E&M – Outgoing System
Speed Dialing
This option Enables or Disables a
DISA or tie trunk caller ability to
use System Speed Dialing.
0 = Off
1 = On
(default = 0 for
COS 1~15)
3
20-14-05 Class of Service Options for
DISA/E&M – Operator Calling
This option Enables or Disables a
DISA or tie trunk caller ability to dial 0
for the telephone system operator.
0 = Off
1 = On
(default = 1 for
COS 1~15)
3
20-14-06 Class of Service Options for
DISA/E&M – Internal Paging
This option Enables or Disables a
DISA or tie trunk caller ability to use
the telephone system Internal
Paging.
0 =Off
1 = On
(default = 1 for
COS 1~15)
3
20-14-07 Class of Service Options for
DISA/E&M – External Paging
This option Enables or Disables a
DISA or tie trunk caller ability to use
the telephone system External
Paging.
0 = Off
1 = On
(default = 1 for
COS 1~15)
3
20-14-08 Class of Service Options for
DISA/E&M – Direct Trunk Access
This option Enables or Disables a
DISA or tie trunk caller ability to use
Direct Trunk Access (Service Code
#9).
0 = Off
1 = On
(default = 0 for
COS 1~15)
3
20-14-09 Class of Service Options for
DISA/E&M – Forced Trunk
Disconnect <Not for ISDN
T-point>
This option Enables or Disables a tie
trunk caller ability to use Forced
Trunk Disconnect (Service Code 3).
This option is not available to DISA
callers.
0 = Off
1 = On
(default = 0 for
COS 1~15)
3
20-14-10 Class of Service Options for
DISA/E&M – Call Forward Setting
by Remote via DISA
Enable or Disable a DISA caller
ability to use the Call Forward service
codes (Programs 11-11-01 ~ 11-11-
05).
0 = Off
1 = On
(default = 0 for
COS 1~15)
3
20-14-11 Class of Service Options for
DISA/E&M – DISA/Tie Trunk
Barge-In
In an extension Class of Service,
enable (1) or disable (0) a DISA or tie
trunk user from using the Barge-In
feature.
0 = Off
1 = On
(default = 0 for
COS 1~15)
3
21-15-01 Individual Trunk Group Routing
for Extensions
Designate the trunk route accessed
when a user dials the Alternate Trunk
Route Access Code. Refer to Trunk
Group Routing to set up outbound
routing.
0~100
(0 = No Setting)
(default = 0)
3
22-01-11 System Options for Incoming
Calls – VRS Waiting Message
Interval Time
Setup the duration time between
announcing the VRS Waiting
Message for Auto – Attendant &
Queuing. The message is repeatedly
sent out in the specified time.
0~64800 (seconds)
(default = 20 seconds)
3
Program
Number
Program Name Description/Comments Assigned Data
Level
1 2 3