ENGLISH – 3
GENERAL SAFETY WARNINGS AND
PRECAUTIONS
1
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.1 GENERAL WARNINGS
a
WARNING! Important safety instructions. Observe all the
instructions as improper installation may cause serious
damages.
a
WARNING! Important safety instructions. It is important
to comply with these instructions to ensure personal
safety. Store these instructions carefully.
WARNING! Please abide by the following warnings:
– Before commencing the installation, check the “Product techni-
cal specications”, in particular whether this product is suitable
for automating your guided part. Should it not be suitable, do
NOT proceed with the installation.
– The product cannot be used before it has been commissioned
as specied in the “Testing and commissioning” chapter.
a
According to the latest European legislation, an automat-
ed device must be constructed in conformity to the har-
monised rules specied in the current Machinery Direc-
tive, which allow for declaring the presumed conformity
of the automation. Consequently, all the operations for
connecting the product to the mains electricity, its com-
missioning and maintenance must be carried out exclu-
sively by a qualied and expert technician.
– Before proceeding with the product’s installation, check that all
the materials are in good working order and suited to the intend
-
ed applications.
– The product is not intended for use by persons (including chil
-
dren) with reduced physical, sensory or mental capacities, nor
by anyone lacking sufcient experience or familiarity with the
product.
– Children must not play with the appliance.
– Do not allow children to play with the product’s control devices.
Keep the remote controls out of reach of children.
a
In order to avoid any danger from inadvertent resetting
of the thermal cut-off device, this appliance must not be
powered through an external switching device, such as a
timer, or connected to a supply that is regularly powered
or switched off by the circuit.
– The system’s power supply network must include a disconnec-
tion device (not supplied) with a contact opening gap permit-
ting complete disconnection under the conditions envisaged by
Overvoltage Category III.
– Handle the product with care during installation, taking care to
avoid crushing, denting or dropping it, or allowing contact with
liquids of any kind. Keep the product away from sources of heat
and naked ames. Failure to observe the above can damage the
product, and increase the risk of danger or malfunction. Should
this happen, stop installation immediately and contact Custom
-
er Service.
– The manufacturer declines all liability for damages to property,
objects or people resulting from failure to observe the assem
-
bly instructions. In such cases, the warranty for material defects
shall not apply.
– The weighted sound pressure level of the emission A is lower
than 70 dB(A).
– Cleaning and maintenance reserved for the user must not be
carried out by unsupervised children.
– Before intervening on the system (maintenance, cleaning), al
-
ways disconnect the product from the mains power supply and
from any batteries.
– Inspect the system frequently, in particular the cables, springs
and supports to detect any imbalances and signs of wear or
damage. Do not use the product if it needs to be repaired or
adjusted, because defective installation or incorrect balancing of
the automation can lead to injuries.
– The packing materials of the product must be disposed of in
compliance with local regulations.
– Keep persons away from the gate when it is manoeuvred using
the control elements.
– When operating the gate, keep an eye on the automated mech
-
anism and keep all bystanders at a safe distance until the move-
ment has been completed.
– Do not operate the product if anyone is working nearby; discon
-
nect its power supply before permitting such work to be done.
– If the power cable is damaged, it must be replaced by the manu
-
facturer or by an appointed servicing company or similarly qual-
ied person in order to prevent any form of risk.
– Warning! Transport the product using the relevant hand trolley
and the handles on the package to ensure that the operations
are conducted safely.
1.2 INSTALLATION WARNINGS
– Prior to installing the drive motor, check that the door is in good
working order, correctly balanced and that it opens and closes
properly.
– Before installing the drive motor, remove all unnecessary ropes
or chains and deactivate any equipment not required for motor
-
ised operation, such as locking devices.
– If the gate being automated has a pedestrian gate, the system
must be equipped with a control device that inhibits the motor’s
operation when the pedestrian gate is open
– Install the manoeuvre device for manual unlocking at less than
1.8 m above the ground. NOTE - If removable, the manoeuvre
device must be kept next to the door when removed.
– Make sure that the control elements are kept far from moving
parts but nonetheless directly within sight. Unless a selector
is used, the control elements must be installed at least 1.5 m
above the ground and must not be accessible.
To Next Page
Loading...
