NORDAC LINK (SK 250E-FDS ... SK 280E-FDS) – Users Manual for Frequency Inverters as Field Distributors
154 BU 0250 en-3021
Pos: 501 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700-P799/Parameter P711 – Zustand Digit ale Ausgänge [SK 2xxE, S K 2xxE-FDS] @ 2\mod_13469322063 90_388.docx @ 43536 @ @ 1
P711
State of relays
(state of digital outputs)
00000 ... 11111 (bin)
or
00 ... FF
(hex)
Indicates the actual status of the digital outputs of the frequency inverter.
Bit 1 = Mechanical brake
Bit 2 = Digital output 2
Bit 4 = Digital output 1, IO extension 1
Bit 5 = Digital output 2, IO extension 1
Bit 6 = Digital output 1, IO extension 2
Bit 7 = Digital output 2, IO extension 2
Pos: 502 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700- P799/Parameter P711 – Zus tand Digitale Ausgäng e_Teil2/2 [SK 1x0E, SK 2 xxE, SK 2xxE-FDS] @ 9\mod_1448448278913_ 388.docx @ 266811 @ @ 1
Bits 3-0
Minimum value
0000
0
0000
0
Binary
hex
Maximum value
1111
F
1111
F
Binary
hex
SimpleBox: The binary bits are converted to a hexadecimal value and displayed.
ParameterBox: The bits are displayed increasing from right to left (binary).
Pos: 503 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700- P799/Parameter P714 – Betri ebsdauer @ 0\mod_132817 2684685_388.docx @ 1266 3 @ @ 1
P714
Operating time
(Operating time)
0.10 ... ___ h
This parameter shows the time for which the FI was connected to the mains and was ready for
operation.
Pos: 504 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700- P799/Parameter P715 – Fr eigabedauer @ 0\mod_13281727 31474_388.doc x @ 12686 @ @ 1
P715
Running time
(Enablement time)
0.00 ... ___ h This parameter shows the time for which the FI was enabled and supplied current to the output.
Pos: 505 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700- P799/Parameter P716 – Akt uelle Frequenz @ 0\mod_132 8172775215_388.doc x @ 12709 @ @ 1
P716
Current frequency
(Actual frequency)
-400.0 ... 400.0 Hz Displays the actual output frequency.
Pos: 506 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P700- P799/Parameter P717 – Akt uelle Drehzahl @ 0\mod_1328 172889966_388.doc x @ 12732 @ @ 1
P717
Current speed
(Actual rotation speed)
-9999 ... 9999 rpm Displays the actual motor speed calculated by the FI.
Pos: 507 /Anleitungen/ Elektronik/F U und Starter/5. Parameter /Parameterauflis tung (P000 ...)/P 700-P799/Parameter P718 – Akt uelle Sollfrequenz @ 0\mod_ 1328172931732_388. docx @ 12755 @ @ 1
P718 [-01]
...
[-03]
Present Actual setpoint
frequency
(Actual setpoint frequency)
-400.0 ... 400.0 Hz
Displays the frequency specified by the setpoint
(chapter 8.1).
[-01] = Actual setpoint frequency from the setpoint source
[-02] = Actual setpoint frequency after processing in the FI status machine
[-03] = Actual setpoint frequency after frequency ramp
Pos: 508 /Allgemein/A llgemeingültige Module/---------Seitenumbruch kompakt --------- @ 13\mod_14763696959 06_0.docx @ 2265495 @ @ 1
To Next Page
Loading...
