Nord Drivesystems NORDAC LINK SK250E-FDS - Page 170

NORDAC LINK (SK 250E-FDS ... SK 280E-FDS) – Users Manual for Frequency Inverters as Field Distributors
170 BU 0250 en-3021
16.1 Magnetisation current
monitoring
"Magnetisation current
monitoring"
Required exciting current not achieved at moment of switch-
on.
• Check P539
• Check motor connection
Pos: 592 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E018 "r eserviert" [SK 2xxE/SK 5xxE/SK 2xxE-FDS, SK 500P] @ 44\mod_1594726433 780_388.docx @ 2645287 @ @ 1
E018
18.0
Reserved
Error message for “Safe Pulse Block”, see supplementary
instructions
Pos: 593 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E019 [ SK 180E/SK 2xxE/SK 5xxE/SK2xxE-FDS, außer SK 500P ] @ 2\mod_1347454285788 _388.docx @ 46876 @ @ 1
E019
19.0 Parameter identification
"Parameter identification"
Automatic identification of the connected motor was
unsuccessful
• Check motor connection
• Check preset motor data (P201 … P209)
• PMSM – CFC Closed Loop Operation: Rotor position
of motor incorrect in relation to incremental encoder
Perform determination of rotor position (initial enable
after a "Mains on" only with motor stationary (P330)
19.1 Star / Delta circuit incorrect
"Motor star / delta circuit
incorrect"
Pos: 594 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E020 / E021 [SK 135E ... SK 5xxE/P, SK xxxE-FDS] @ 2\mod_134745428 8768_388.docx @ 46901 @ @ 1
E020
E021
20.0 Reserved
System error in program execution, triggered by EMC
interference.
•
Observe wiring guidelines
•
Use additional external mains filter.
•
FI must be very well earthed.
20.1 Watchdog
20.2 Stack overflow
20.3 Stack underflow
20.4 Undefined opcode
20.5 Protected Instruct.
"Protected Instruction"
20.6 Illegal word access
20.7 Illegal Inst. Access
"Illegal instruction access"
20.8 Program memory error
"Program memory error"
(EEPROM error)
20.9 Dual-ported RAM
21.0 NMI error
(Not used by hardware)
21.1 PLL error
21.2 ADU error "Overrun"
21.3 PMI error "Access Error"
21.4 Userstack overflow
Pos: 595 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E022 "r eserviert" - PLC [SK 180E ... SK 5xxE/SK 500P] @ 2\mod_1361527702934_388.doc x @ 59091 @ @ 1
E022
--- Reserved
Error message for PLC  see supplementary instructions
BU 0550
Pos: 596 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E023 "r eservi ert" - PLC [SK 180E ... SK 5xxE/SK 500P] @ 2\mod_13615278081 70_388.docx @ 59116 @ @ 1
E023
--- Reserved
Error message for PLC  see supplementary instructions
BU 0550
Pos: 597 /Anleitungen/ Elektronik/F U und Starter/6. Meldungen zu m Betriebszustand/Stör meldungen (Auflis tung)/Fehler E024 "r eserviert" - PLC [SK 180E ... SK 5xxE/ SK 500P] @ 6\mod_1423644411761_388.doc x @ 201828 @ @ 1
E024
--- Reserved
Error message for PLC  see supplementary instructions
BU 0550