9 - 11
9 LX inverter
Drive Programming User’s Manual (I580-E2)
9-4 Drive Programming User Variables
9
9-4-3 Multi-function Output Variables
Note The LX inverter functions are available for the digital multifunction input terminals P140 to P144 (Multi-Input
[ExIN1-5) with the 3G3AX-EIO-E extra I/O board.
Note The LX inverter functions are available for the digital multifunction output terminals P145 to P147
(Multi-Output [ExOUT1-3) with the 3G3AX-EIO-E extra I/O board.
NFS Near floor signal R/W C001 to C007 75
PRG Program run R/W C001 to C007 76
CMC Control mode change R/W C001 to C007 77
GS1 Gate suppress 1 R/W C001 to C007 78
GS2 Gate suppress 2 R/W C001 to C007 79
9-4-3 Multi-function Output Variables
Function variable Description R/W Reference
RUN Signal during RUN R C021 to C023, C026: 00
FA1 Constant speed arrival signal R C021 to C023, C026: 01
FA2 Set frequency exceeded signal R C021 to C023, C026: 02
OL Overload warning R C021 to C023, C026: 03
AL Alarm signal R C021 to C023, C026: 05
FA3 Set frequency only signal R C021 to C023, C026: 06
OTQ Overtorque/Undertorque signal R C021 to C023, C026: 07
IP Signal during momentary power interruption R C021 to C023, C026: 08
UV Signal during undervoltage R C021 to C023, C026: 09
TRQ Torque limit R C021 to C023, C026: 10
RNT RUN time over R C021 to C023, C026: 11
ONT Power ON time over R C021 to C023, C026: 12
THM Electronic thermal warning R C021 to C023, C026: 13
ZS 0 Hz detection signal R C021 to C023, C026: 14
POK Position ready R C021 to C023, C026: 16
FA4 Set frequency exceeded signal 2 R C021 to C023, C026: 17
FA5 Set frequency only signal R C021 to C023, C026: 18
OL2 Overload warning 2 R C021 to C023, C026: 19
TH-C Thermal alarm signal R C021 to C023, C026: 20
NDc Communications disconnection detection R C021 to C023, C026: 23
WAC Capacitor life warning signal R C021 to C023, C026: 30
WAF Cooling fan life warning signal R C021 to C023, C026: 31
FR Starting contact signal R C021 to C023, C026: 32
OHF Cooling fin overheat warning R C021 to C023, C026: 33
LOC Low current signal R C021 to C023, C026: 34
Y(00) to Y(06) Drive Programming MO1 to MO7 R C021 to C023, C026: 35 to 41
IRDY Operation ready R C021 to C023, C026: 44
FWR Forward run signal R C021 to C023, C026: 45
RWR Reverse run signal R C021 to C023, C026: 46
MJA Fatal fault signal R C021 to C023, C026: 47
CON Contactor control signal R C021 to C023, C026: 51
BRK Brake control signal R C021 to C023, C026: 52
UPS UPS protect direction search status R C021 to C023, C026: 54
UPD UPS protect direction R C021 to C023, C026: 55
GMON Gate suppress monitor R C021 to C023, C026: 56
MPS Magnet pole position search R C021 to C023, C026: 57
SEQ SEQ error R C021 to C023, C026: 58
Function variable Description R/W Reference
To Next Page
Loading...
