– 87 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
[F] Displayed when the <AUDIO IN> switch is <FRONT>.
[W] Displayed when the <AUDIO IN> switch is <W.L.>.
[R] Displayed when the <AUDIO IN> switch is <REAR>.
20 Iris override display
Displays the compensation level when the iris overwrite is functioning.
[++]
Aperture opens by about 1.
[+]
Aperture opens by about 0.5.
[−−]
Aperture closes by about 1.
[−]
Aperture closes by about 0.5.
(No display) Reference state.
21 Super iris display
Displayed when super iris is active.
22 Iris, F value
[NC] Displayed when the lens cable is not connected.
[OPEN] Displayed when the lens aperture is open.
[F1.7] to [F16] Displays the lens aperture value.
[CLOSE] Displayed when the lens aperture is closed.
f Displayed when a lens with an aperture value display function is used. Also, ashes when the iris override is variable.
23 Super black display
Displayed when super black is active.
24 Zoom display
[Z00] to [Z99]
Displays the zoom amount. Note, however, that this item is not displayed in the case of lenses without a zoom position return
even if it is set to be displayed.
[Z**.*mm]
When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/
FOCUS].
25 Focus control information
Displays the focus control information with [99] to [00]. When a lens other than a serial lens is connected, the focus control information is not
displayed. When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/FOCUS].
26 Information display such as interval recording/pre-recording
[i] Displayed before recording starts and after recording ends during interval recording.
[i-REC] (ashing) Displayed during recording in interval recording.
[i-REC] (ashing)
[**h**m/**s]
During interval recording standby, displays the standby time until the next recording.
[P-REC] (ashing)
Displayed after recording is stopped and until recording of video/audio to P2 card completely stops. Do not remove the P2 card
or turn the power off until the ashing indication completely goes out.
f When the pre-recording function is set to [OFF], [REC] ashes.
[P-REC *s/OFF]
(illuminated)
Illuminated if the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch is pushed towards the <MCK/MCL> side when the
pre-recording function is set to [ON]. The status is displayed when the <USER> button where [PRE REC] is assigned is pressed
to switch to the pre-recording mode.
[1-CLIP] Displayed when [ONE CLIP REC] is [ON], and a new clip is going to be recorded.
[1*CLIP]
Displayed when [ONE CLIP REC] is [ON], and recording can be linked to the previous clip.
f If the previous clip no longer exists due to removal of the P2 card or deletion of the clip, the next recording will start as a new
clip. In this case, the display may remain as [1*CLIP].
[START 1*CLIP]
Displayed when recording of a new clip is started in [ONE CLIP REC].
[END 1-CLIP] Displayed when linking of clips is ended in [ONE CLIP REC].
27 Gamma mode display
Displays the gamma mode currently selected by [GAMMA MODE SEL] in the main menu → [PAINT] → [GAMMA].
[HD]/[SD]/[FLK1]/[FLK2]/[FLK3]/[FREC]/[VREC]
28 Lock status display of auto tracking white balance
Displayed when the <USER> button where [ATW LOCK] is assigned is pressed and the color temperature is xed while auto tracking white balance
is active.
29 Type of marker
Displays the type of currently displayed marker.
[MKR:A/B/OFF]
30 Network information display
[WLAN] Displayed when the wireless LAN is operating properly.
[WLAN
]
Displayed when the wireless LAN is not operating properly.
[LAN] Displayed when the wired LAN is operating properly.
[LAN
]
Displayed when the wired LAN is not operating properly.
31 Streaming setting status display
Displays the setting status of the streaming function.
To Next Page
Loading...
