List of Figures
Figure 1: Saw blade ................................................................................................................................................................................ 8
Figure 2: Danger zone saw blade ......................................................................................................................................................... 20
Figure 3: Danger zones around the machine ....................................................................................................................................... 20
Figure 4: Cutting short workpieces to width ........................................................................................................................................ 21
Figure 5: Fixing the deflector wedge on the table ............................................................................................................................... 22
Figure 6: Nameplate ............................................................................................................................................................................ 23
Figure 7: Working areas ....................................................................................................................................................................... 26
Figure 8: Dimensions (front view) ........................................................................................................................................................ 26
Figure 9: Dimensions (top view) .......................................................................................................................................................... 27
Figure 10: Machine transport .............................................................................................................................................................. 28
Figure 11: Levelling screws at the rear (normal case) .......................................................................................................................... 29
Figure 12: Front levelling screws (exceptional case) ............................................................................................................................ 29
Figure 13: Lashing points (4 x) ............................................................................................................................................................. 30
Figure 14: Upper suction nozzle diameter ........................................................................................................................................... 31
Figure 15: Lower suction nozzle diameter ........................................................................................................................................... 31
Figure 16: Electrical connection ........................................................................................................................................................... 32
Figure 17: Components & controls - front view ................................................................................................................................... 33
Figure 18: Components & controls - top view ..................................................................................................................................... 34
Figure 19: Slide table controls ............................................................................................................................................................. 35
Figure 20: Rip fence ............................................................................................................................................................................. 35
Figure 21: Fitting the rip fence ............................................................................................................................................................ 36
Figure 22: Operating the rip fence ....................................................................................................................................................... 36
Figure 23: Cross slide mounting ........................................................................................................................................................... 37
Figure 24: Cross slide clamping ............................................................................................................................................................ 37
Figure 25: Moving the cross slide ........................................................................................................................................................ 37
Figure 26: Swivel arm for saw blade guard .......................................................................................................................................... 38
Figure 27: Fitting the saw blade guard ................................................................................................................................................ 38
Figure 28: Control elements ................................................................................................................................................................ 39
Figure 29: Flip stop with measuring scale and magnifying glass .......................................................................................................... 41
Figure 30: Cross-cut fence operating elements ................................................................................................................................... 41
Figure 31: Fixing screw ........................................................................................................................................................................ 41
Figure 32: Start screen ......................................................................................................................................................................... 42
Figure 33: Status window .................................................................................................................................................................... 42
Figure 34: Language settings ............................................................................................................................................................... 43
Figure 35: Machine overview - current positions and speed ............................................................................................................... 43
Figure 36: Saw blade height 50 mm..................................................................................................................................................... 44
Figure 37: Calibrate height .................................................................................................................................................................. 44
Figure 38: Adopt calibration value for height ...................................................................................................................................... 44
Figure 39: Angular gap ......................................................................................................................................................................... 45
Figure 40: Calibrate angle .................................................................................................................................................................... 45
Figure 41: Adopt calibration value for angle ........................................................................................................................................ 45
Figure 42: Set date and time ................................................................................................................................................................ 46
Figure 43: Speed setting - loosen V-belt .............................................................................................................................................. 46
Figure 44: Speed scheme ..................................................................................................................................................................... 46
Figure 45: Remote locking on the slide table ....................................................................................................................................... 47
Figure 46: Safety catch on the slide table ............................................................................................................................................ 47
Figure 47: Fold sawdust flap forwards ................................................................................................................................................. 47
Figure 48: Saw blade flange ................................................................................................................................................................. 47
Figure 49: Riving knife setting (symbolic representation).................................................................................................................... 48
Figure 50: Tele-Digit cross-cut fence.................................................................................................................................................... 49
Figure 51: Fixing points on the cross slide ........................................................................................................................................... 49
Figure 52: Tele-Digit components ........................................................................................................................................................ 50
Figure 53: Digital indicator ................................................................................................................................................................... 50
Figure 54: Error message FULL............................................................................................................................................................. 52
Figure 55: Rip fence mounted to the left of the saw blade ................................................................................................................. 53
Figure 56: Flip stop (left to the saw blade) .......................................................................................................................................... 53
Figure 57: DSG-A (analogue) ................................................................................................................................................................ 53
Figure 58: DSG-D (with digital indicator) ............................................................................................................................................. 53
Figure 59: Super Gehrfix I .................................................................................................................................................................... 54
Figure 60: Super Gehrfix I overview ..................................................................................................................................................... 55
To Next Page
Loading...