Paradox EVOHD+

To Previous Page

The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction.

Should you have any questions or comments, please contact us at support@paradox.com.

Additional information can be found on our website www.paradox.com/support

Printed in Canada - 11/2022 PARADOX.COM EVOHD+-EI00

Main Page

Table of Contents3
Introduction5
Features of EVOHD5
Specifications5
EN 50131 Compliancy6
Installation7
Recommended Installation Procedure7
Location & Mounting7
EVOHD+ Control Panel Installation7
Earth Ground7
AC Power7
Backup Battery8
Auxiliary Power Terminals8
Bell/Siren Output8
Programmable Outputs8
Keyswitch Connections8
Access Control Connections8
Keypad Installation (K641R/K641+)9
Keypad Specifications (K641R/K641+ Only)9
Unlock Panel Serial Ports9
Calculating Power Requirements11
Keypad Zone Connections14
Addressable Zone Connections14
Double Zone Connections16
Digiplex Bus Connections16
Fire Circuits17
Telephone Line Connections17
Programming Methods18
Babyware Uploading/Downloading Software18
Module Broadcast18
Programming through a Keypad18
Module Programming Mode19
Zone Programming20
Zone Programming21
Zone Numbering21
Zone Doubling (ATZ)21
Zone Definitions21
Zone Partition Assignment23
Zone Options23
Input Speed26
EOL on Hardwire Zones26
Selectable Input Resistor26
Keypad Numbering26
Remote Control Programming27
Hardware Requirements27
Remote Control Template27
Remote Control Templates27
Keyswitch Programming29
Keyswitch Numbering29
Keyswitch Definitions29
Keyswitch Partition Assignment30
Keyswitch Options30
Arming and Disarming Options31
Arming Follows Partition31
Trouble Latch31
Restrict Arming on Supervision Loss31
Restrict Arming on Tamper31
Restrict Arming on AC Failure31
Restrict Arming on Battery Failure31
Restrict Arming on Bell or Auxiliary Failure31
Restrict Arming on TLM Failure31
Restrict Arming on Module Troubles31
Timed Auto-Arming32
No Movement Auto-Arming33
Auto-Arming Options33
Switch to Stay Arming33
Always Force Arm When Regular Arming33
Auto Force on Stay Arming33
Follow Zone Switches to Entry Delay 234
One-Touch Features34
Exit Delay34
Keypad Lock-Out Feature34
Bell Squawk35
Ring-Back35
Maximum Bypass Entries35
Display "Bypass" if Armed35
Alarm Options36
Bell/Alarm Output36
Bell Cut-Off Timer36
Wireless Transmitter Supervision Options36
Police Code Timer37
Tamper Recognition Options37
Keypad Panic Options38
Event Reporting39
Reporting Enabled40
IP/ PCS / GPRS Reporting40
Report Codes40
Report Arming and Disarming44
Monitoring Station Phone Number45
Account Number45
Account Number Transmission45
Reporting Formats45
Event Call Direction46
Recent Close Delay47
Power Failure Report Delay47
Power Failure Restore Report Delay47
Auto Test Report47
Disarm Reporting Options48
Zone Restore Report Options48
Auto Report Code Programming48
Closing Delinquency Timer48
Dialer Options49
Telephone Line Monitoring49
Tone/Pulse Dialing49
Pulse Ratio49
Busy Tone Detection49
Switch to Pulse49
Bell on Communication Fail49
Keypad Beep on Successful Arm or Disarm Report49
Dial Tone Delay49
VDMP3 Voice Module50
VDMP3 Installation Instructions50
Feature Activation50
VDMP3 Setup Instructions51
Programmable Outputs52
PGM Programming52
PGM1 Becomes a 2-Wire Smoke Detector Input52
System Settings and Commands53
Hardware Reset53
Software Reset53
Installer Code Lock53
Daylight Savings Time53
Daylight Savings Time Schedule54
Digiplex Bus Speed54
Transmit Zone Status on Serial Port54
Partitioning54
Shabbat Feature54
Installer Function Keys55
Module Reset55
Locate Module55
Module Programming55
Module and Label Broadcast55
System Date & Time55
Re-Address Scanning (TM50/TM70 Keypads Only)56
Quarantine Modules (TM50/TM70 Keypads Only)56
Serial Number Viewing56
Power Save Mode56
Auto Trouble Shutdown56
No AC Fail Display56
Multiple Action Feature56
System Labels57
Access Codes60
Installer Code60
Access Code Length60
System Master Code60
Programming Access Codes60
User Options60
Partition Assignment62
Access Control62
Access Control: System Features64
Common Access Control Terms64
Programming Overview64
Enable Access Control64
Door Numbering64
Access Levels65
Access Schedules65
Backup Schedules65
Holiday Programming65
Schedule Tolerance Window65
Door Access Mode66
Code Access66
Card and Code Access66
Skip Exit Delay When Arming with Access Card66
Restrict Arming on Door66
Restrict Disarming on Door66
Door Access During Clock Loss66
Burglar Alarm on Forced Door or Door Left Open67
Logging Access Control Events67
Babyware Software68
Panel Identifier68
PC Password68
PC Telephone Number68
Call Back Feature68
Call Babyware68
Answering Machine Override Delay68
Ring Counter68
Event Buffer Transmission68
In-Field Firmware Upgrade68
Appendix 1: Automatic Report Code List70
Appendix 2: Contact ID Report Code List73
Appendix 3: Keypad Installation Instructions75
Index83

Table of Contents

Related product manuals