Particle Measuring Systems LASAIR II 550L Operator's Manual


Page Page M-6 M-6 LASAIR LASAIR II II Operator’s Operator’s ManualManual
Appendix M: TouchRamAppendix M: TouchRam
TTouchRAM Buttons with ouchRAM Buttons with TCP/IP AddressTCP/IP Address
In facilities with Pharmaceutical Net software, data sampled at various locationsIn facilities with Pharmaceutical Net software, data sampled at various locations
can be conveniently downloaded to Pharmaceutical Net, and then analyzed andcan be conveniently downloaded to Pharmaceutical Net, and then analyzed and
archived. In large facilities with several Pharmaceutical Net installations, it mayarchived. In large facilities with several Pharmaceutical Net installations, it may
be beneficial to be able to automatically change the TCP/IP address of thebe beneficial to be able to automatically change the TCP/IP address of the
LASAIR II when it is moved from one PharmaceuLASAIR II when it is moved from one Pharmaceutical Net area to another.tical Net area to another.
TTouchRAM buttons can have ouchRAM buttons can have a TCP/IP address programmed in them, whicha TCP/IP address programmed in them, which
facilitates this facilitates this capabilitycapability..
Setting the TCP/IP Address Setting the TCP/IP Address in a TouchRAM Buttonin a TouchRAM Button
FigureFigure M-2, belowM-2, below, shows the LASAIR I, shows the LASAIR II Comm Setup Screen. The “Serial”I Comm Setup Screen. The “Serial”
page shown ipage shown in the ln the left side eft side sets the sets the function of function of the serial the serial port. Tport. To read and o read and writewrite
TTouchRAM buttons, ouchRAM buttons, “T“TouchRAM Read/Write” must be ouchRAM Read/Write” must be selected. Buttons canselected. Buttons can
be written with or without the TCP/IP address. In order to wrbe written with or without the TCP/IP address. In order to write the TCP/IPite the TCP/IP
address, the “TouchRAM Waddress, the “TouchRAM Write TCP/IP” button must be selected rite TCP/IP” button must be selected on the “Data”on the “Data”
screen. If this setting is disabled, a 0.0screen. If this setting is disabled, a 0.0.0.0 is written for the TCP/IP address. Th.0.0 is written for the TCP/IP address. Thee
0.0.0.0 is ignored when the button is read.0.0.0.0 is ignored when the button is read.
Rules for Reading TouchRAM ButtonsRules for Reading TouchRAM Buttons
TTo read a o read a button, the serial setup button, the serial setup must be either “TouchRAM Read” ormust be either “TouchRAM Read” or
“T“TouchRAM Read/Write”. The Data ouchRAM Read/Write”. The Data page setting page setting of “TouchRAM Write TCP/of “TouchRAM Write TCP/
IP” has no effect when reading buttons. In IP” has no effect when reading buttons. In other words, even if this setting isother words, even if this setting is
disabled, the TCP/IP address will be read and disabled, the TCP/IP address will be read and processed from a button.processed from a button.
The following processing occurs when a button is read:The following processing occurs when a button is read:
•• If the TCP/IP address is read as 0.0.0.0, nIf the TCP/IP address is read as 0.0.0.0, no additional processing occurs.o additional processing occurs.
•• If the TCP/IP address is the same as the onIf the TCP/IP address is the same as the one on the LASAIR II, then noe on the LASAIR II, then no
additional processing occurs.additional processing occurs.
Figure M-2: Comm Setup Screens for Configuring TouchRAMFigure M-2: Comm Setup Screens for Configuring TouchRAM

Particle Measuring Systems LASAIR II 550L Specifications

General

Brand	Particle Measuring Systems
Model	LASAIR II 550L
Category	Measuring Instruments
Language	English