Peterbilt 220 - Noise and Emissions Requirements

To Next Page

To Previous Page

2-3

Section 2

Safety & Compliance

Noise and Emissions Requirements

NOTE:

This truck may be equipped with a converter mufﬂer unit in order to meet both noise and exhaust

emissions requirements. Removal or tampering with the converter mufﬂer will not improve engine per-

formance. Also tampering is against the rules that are established by the U.S. Code of Federal Regu-

lations and Environment Canada Regulations. The converter mufﬂer may only be replaced with an

approved part.

Relocation of converter mufﬂer will affect noise and emission performance. Contact the engine manu-

facturer for any requirements and restrictions prior to any modiﬁcations. In particular, there are re-

quirements and restrictions for exhaust pipe materials and for maximum exhaust system lengths from

turbo outlet to mufﬂer inlet.

Main Page

Table of Contents3
Figures5
Abbreviations8
Section1 Introduction10
Safety Signals11
Federal Motor Vehicle Safety Standards Compliance12
- Incomplete Vehicle Certiﬁcation12
- Noise and Emissions Requirements13
Table 3-1 Frame Height14
Section3 Dimensions14
Frame Height14
Table 3-2 Turning Radius15
Turning Radius15
Cab Tilt16
- Model 220 W/19.5 Tires16
- Model 220 W/22.5 Tires16
- Figure 3-1.1 Side View -Model 220 W/19.5 Tires Cab Tilt Height and Pivot Location Measurement16
- Figure 3-1.2 Side View -Model 220 W/22.5 Tires Cab Tilt Height and Pivot Location Measurement16
- Table 3-3 Cab Tilt Height16
- Table 3-4 Cab Pivot Location16
Overall Dimensions17
- Side View - Model 22017
- Table 3-5 Overall Dimensions18
- Front and Rear Views - Model 22020
- Figure 3-3.1 Front & Rear View -Model 22020
Detail Views3-1023
- Left Side: Chassis Heights - Model 22023
- Figure 3-4.1 Cab Floor: Side View, Left Side W/ 19.5 Tires23
- Table 3-7.1 Battery Box Step and Cab Floor Measurements W/ 19.5 Tires23
- Table 3-7.2 Battery Box Step and Cab Floor Measurements W/ 22.5 Tires24
- Figure 3-4.2 Cab Floor: Side View, Left Side W/ 22.5 Tires24
- Components Locations -Model 22025
- Figure 3-5.1 Model 220 W/22.5 Tires, Battery Box, Fuel Tank, Air Tank, DEF Tank and Crossmember Location Measured from Front Axle: Inches (MM)25
- Crossmember Locations-Model 22027
- Figure 3-6.1 Model 220 Crossmember Locations27
- Table 3-9.1 Model 220 Crossmember Location Measured from Front Axle Centerline27
- Frame Rail Configurations29
- Figure 3-7 Model 220 Rail Measurements29
- Table 3-10 Frame Rail Strength Characteristics29
- Battery Box, Fuel Tanks and Air Tanks - Model 22030
- Figure 3-8 Model 220 Battery Box, Fuel Tank and Air Tanks Measurement MM (In)30
- DPF & SCR Locations -Model 22031
- Figure 3-9.1 Model 220 Exhaust Measurements31
- Figure 3-9.2 Model 220 Exhaust Measurements31
- Table 3-11 Model 220 Exhaust Location Measured from BOC Inches (MM)31
- Table 3-12 Model 220 Exhaust Location Measured from BOC Inches (MM)31
- Side View - Model 220 Clear Rail Package32
- Figure 3-10.1 Side View -Model 220 CRP Laden Height and Length Measurement32
- Reyco 79KB Single Rear Axle Hendrickson HAS Single Rear Axle33
Table 3-13 Model 220 Reyco & Hendrickson Single Rear Axle: Ride Height Measurement33
Figure 3-11 Model 220 Reyco & Hendrickson Single Rear Axle Measurements33
Tire Data33
Frame and Cab Related Heights33
Ground Clearances33
Figure 3-12.1 PTO Models Installed on a 2000 Series Allison Transmission34
Pto Clearances34
Figure 3-12.2 Model 220 PTO Clearances 1 of 235
Figure 4-1.1 the DEF Lines Route to the After-Treatment System36
Exhaust and Aftertreatment Information36
- Figure 4-1.2 the DEF Lines Route to the Engine Coolant37
- General Guidelines for DEF System38
- Installation Requirements and Dimensions for DEF System38
- Figure 4-2 Measurement Location of DEF Supply Module (Pump)39
- Figure 4-3 Measurement Location of DEF Dosing Module (Injector)39
- Measurement Reference Points39
- Figure 4-4 Orientation of Dosing Module40
- Figure 4-5 Routing DEF Lines and DEF Trap40
- Routing to the Dosing Module (Injector)40
Figure 4-6.1 Horizontal Crossover DPF and SCR with Horizontal Tailpipe41
Figure 4-6.2 Top View of Horizontal Crossover DPF and SCR with Horizontal Tailpipe41
General Exhaust Information41
Figure 4-6.3 Right View of Horizontal Crossover DPF and SCR with Horizontal Tailpipe42
Figure 4-6.4 Back View of Horizontal Crossover DPF and SCR with Horizontal Tailpipe42
Frame Layouts45
- Visual Index45
- Table 5-1 Symbols45
- Section5 Frame Layouts and Bodymounting FRAME LAYOUTS45
- Figure 5-1.1 Horizontal Crossover DPF/SCR, LH Horizontal Tailpipe, RH BOC Rectangular Fuel Tank, RH BOC Rectangular DEF Tank and LH BOC Battery Box46
- Figure 5-1.2 Horizontal Crossover DPF/SCR, LH Horizontal Tailpipe, RH BOC Rectangular Fuel Tank, RHBOC Rectangular Fuel Tank, RH BOC Rectangular DEF Tank and LH BOC Battery Box46
- Figure 5-1.3 Vertical Crossover DPF/SCR, LH Horizontal Tailpipe, RH BOC Rectangular Fuel Tank, RH47
Critical Clearances48
- Rear Wheels and Cab48
- Figure 5-2 Minimum Clearance between Top of Rear Tires and Body Structure Overhang48
- Figure 5-3 Minimum Back of Cab Clearance48
- Body Mounting Using Brackets49
- Frame Sill49
- Brackets50
- Mounting Holes50
- Figure 5-4 Spacer between Frame Sill and Body Rail - Rubber or Plastic50
- Figure 5-5 High Compression Spring between the Mounting Bolt and Upper Bracket50
- Figure 5-7 Hole Locations Guidelines for Frame Rail and Bracket50
- Frame Drilling51
- Hole Location Guidelines51
Body Mounting Using U-Bolts51
- Spacers51
- Figure 5-9 Acceptable U-Bolt Mounting with Wood and Fabricated Spacers52
- Figure 5-10 Clearance Space for Air Lines and Cables52
Figure 5-11 Example of Fishplate Bracket at Rear End of Body, Used with U-Bolts53
Rear Body Mount53
Section6 Frame Modiﬁcations54
- Frame Modifications54
  - Introduction54
- Drilling Rails54
- Modifying Frame Length54
- Changing Wheelbase54
- Crossmembers55
- Torque Requirements56
- Table 6-1 Customary Grade 8 UNF or UNC56
Section7 Electrical57
- Electrical Introduction57
- Electrical Circuits57
  - Capacity57
  - Data Bus Communication58
- Cab/Chassis Interface59
- Controllers62
- Dash Controls63
- Figure 7-6.1 Power Distribution Center64
- Figure 7-6.2 Power Distribution Center (Chassis)65
- Table 7-1 Additional Spare Circuits for Wiring65
- Figure 7-7 Body Builder 9 Pin Connector66
- Table 7.2 Body Builder 9 Pin Connector66
- Model 220 Pto Wiring Information67
- Figure 7-8.1 Typical PTO Wiring for Euro 6 LFNA - 12V PTO Solenoid68
- Figure 7-8.2 Typical PTO Wiring for Euro 6 LFNA - 24V PTO Solenoid69
- Figure 7-9 a 12-Pin Deutsch Connector and Remote PTO Controls70
Table A-1. Model Year (Code) Designations71
- Certification Labels72
- Component Identification73
Appendix A Vehicle Identiﬁcation71
- Vehicle Identification Number71
  - VIN Location71
  - Chassis Number Locations71
Appendix B Weight Distribution75
- Introduction75
  - Abbreviations75
- Calculations76
Table B-3 Available Model 220 Body Lengths83

Peterbilt 220 - Noise and Emissions Requirements

Table of Contents

Other manuals for Peterbilt 220

Related product manuals