PDP-5000EX
149
5678
56
7
8
C
D
F
A
B
E
Command
Division
Function
command
Reception Point
Last
Memory
Only
FAY is
Effective
Remarks
R
RBL S∗∗ FNC Setting of blue level for panel degradation correction
¶
Mod
¶
RGL S∗∗ FNC Setting of green level for panel degradation correction
¶
Mod
¶
RHI ∗∗∗ ADJ User white balance - Red highlight
¶¶
Main
UP/DW key not effective
RLW ∗∗∗ ADJ User white balance - Red low light
¶¶
Main
UP/DW key not effective
RRL S∗∗ FNC Setting of red level for panel degradation correction
¶
Mod
¶
RSW ∗∗∗ ADJ Adjustment of the width of XY reset pulse 1
¶
Mod
¶
UP/DW key not effective
RYW ∗∗∗ ADJ Adjustment of the width of XY reset pulse 2
¶
Mod
¶
UP/DW key not effective
S
SDM S00 FNC Shutdown enabled
¶
S01 FNC Shutdown prohibited
¶
SFR S01 FNC Measures against AM radio noise - Pattern 1
¶
Mod
¶
S02 FNC Measures against AM radio noise - Pattern 2
¶
Mod
¶
S03 FNC Measures against AM radio noise - Pattern 3
¶
Mod
¶
S04 FNC Measures against AM radio noise - Pattern 4
¶
Mod
¶
S05 FNC Measures against AM radio noise - Pattern 5
¶
Mod
¶
S06 FNC Measures against AM radio noise - Pattern 6
¶
Mod
¶
S07 FNC Measures against AM radio noise - Pattern 7
¶
Mod
¶
S08 FNC Measures against AM radio noise - Pattern 8
¶
Mod
¶
SMM S∗∗ FNC Setting of the effective area during streaking correction
¶¶
SN0 ∗∗∗ ADJ Setting of the serial No. 0 (panel)
¶
Mod
¶
UP/DW key not effective
Alphabetics can be input.
SN1 ∗∗∗ ADJ Setting of the serial No. 1 (panel)
¶
Mod
¶
UP/DW key not effective
Alphabetics can be input.
SN2 ∗∗∗ ADJ Setting of the serial No. 2 (panel)
¶
Mod
¶
UP/DW key not effective
Alphabetics can be input.
SN3 ∗∗∗ ADJ Setting of the serial No. 3 (panel)
¶
Mod
¶
UP/DW key not effective
Alphabetics can be input.
SN4 ∗∗∗ ADJ Setting of the serial No. 4 (panel)
¶
Mod
¶
UP/DW key not effective
Alphabetics can be input.
SSI S01 FNC Sub input switch: INPUT 1
¶
Main
S02 FNC Sub input switch: INPUT 2
¶
Main
S03 FNC Sub input switch: INPUT 3
¶
Main
S04 FNC Sub input switch: INPUT 4
¶
Main
S05 FNC Sub input switch: INPUT 5
¶
Main
S06 FNC Sub input switch: INPUT 6
¶
Main
SSM S00 FNC Turning the external SSCG operation off
¶¶
S01 FNC Turning the external SSCG operation on (normal operation)
¶¶
SZM S00 FNC Setting the screen size to Dot by Dot or PARTIAL
¶
Main
S01 FNC Setting the screen size to 4 : 3
¶
Main
S02 FNC Setting the screen size to FULL or FULL 1080i
¶
Main
S03 FNC Setting the screen size to ZOOM
¶
Main
S04 FNC Setting the screen size to CINEMA
¶
Main
S05 FNC Setting the screen size to WIDE
¶
Main
S06 FNC Setting the screen size to FULL 14 : 9
¶
Main
S07 FNC Setting the screen size to CINEMA 14 : 9
¶
Main
S08 FNC Setting the screen size to FULL 1035i
¶
Main
Mod Main
To Next Page
Loading...
