Piper Cherokee Six - Page 5

PIPER CHEROKEE SIX SERVICE MANUAL
LIST
OF ILLUSTRATIONS
(cont)
Figure Aerofiche
Grid No.
4-7. Repairing
of Cracks .......................................
1F12
4-8. Various Repairs ........................................... 1F13
4-9. Repair of Stress Lines ..................................... 1F14
4-10. Repair of Impacted Damage ................................ IF15
4-11. Wing
Rib Modification ....................................
1F20
4-12. Balance Weight Assembly Installation ........................ 1F20
4-13.
Flap Modification
.....................
....................
1
F21
4-14. Additional Drain Holes in Stabilator ......................... 1F22
4-15. Control
Surface Balance Tool ......................
......... 1G1
4-16. Stabilator Balance ......................................... 1G2
4-17. Aileron Balance .................... ...................... 1G3
4-18. Seat Back Lock
...........................................
IG5
4-19.
Door Snubber Installation
.................. ...............
1G7
5-1. Control Column Assembly (PA-32-260 and 300) ............... IG18
5-1a. Control Column Assembly (PA-32R-300) ..................... 1G20
5-1b. Correct Method of Installing Rod End Bearings ............... IG21
5-2. Aileron
Controls (Typical) ..................................
1G24
5-3. Bellcrank Rigging Tool ........................... ......... I H4
5-4. Aileron Rigging Tool ...................................... 1H4
5-5. Stabilator Controls ........................................ 1H 8
5-6. Stabilator Rigging Tool .................................... 1H9
5-7. Methods of Securing Trim Cables ........................... 1H 11
5-8. Stabilator Trim Controls ................................... 1 H 12
5-9.
Rudder and Steering Pedal Assembly
(Typical) ................
I H1
5-10. Rudder Controls .......................................... 1H22
5-11. Rudder Rigging
Tool ......................................
1H2
5-12. Clamping
Rudder Pedals ...................................
1H23
5-13. Rudder
and Stabilator Travel Adjustment
....................
1H24
5-14. Rudder Trim Control
......................................
112
5-15. Flap Controls
.............................................
114
5-16. Flap Step
Adjustment ......................................
117
5-17.
Flap Rigging Tool
.........................................
117
5-18.
Fabricated Aileron Bellcrank
Rigging Tool ...................
119
5-19. Fabricated Aileron
and Flap Rigging Tool ....................
1110
5-20. Fabricated Stabilator
Rigging Tool ..........................
1111
5-21. Fabricated
Rudder Rigging Tool ............................
1112
5A-1. Schematic Diagram of
Hydraulic System .....................
IJI
5A-2. Hydraulic System Installation ............................... 1J2
5A-3. Hydraulic
Pump/Reservoir, Exploded View
................... 1J8
5A-4.
Test and Adjustment of Hydraulic
Pump .....................
1J9
5A-5. Checking Aligning Brackets of Gear Back-Up Extender
Actuator
..... .........................................
1 J 12
5A-6. Gear Back-Up
Extender Actuator ...........................
1J
13
5A-7. Nose
Gear Actuating Cylinder ..............................
1J19
5A-8. End
Gland Locking
Device (Main Gear)
.....................
J20
5A-9.
Main Gear Actuating
Cylinder
..............................
1J20
5A-10.
Gear
Back-Up
Extender
Actuator
Aligning
Tool
..............
I K I
6-1.
Nose Gear Oleo
Strut Assembly
............................
2A12
Revised:
12/15/80
1A5