Plockmatic BLM 50

To Next Page

To Previous Page

2 3

NOTE:

How to connect cables, plugs and jumpers is described at the end of this manual.

1. Belt Stacker Connector

2. Upstreams Communication

3. Downstreams Communication

4. Power Connection

5. Printer interface

Booklet Maker, continued

Main Page

Default Chapter7
- Table of Contents7
What You Can Do with this Machine11
Guide to Components13
- Booklet Maker13
- User Interface16
  - Control Panel16
Options19
- Rotate Crease Trim Module19
- Booklet Maker24
  - Alive Logo24
  - Cover Feeder25
- Bookfold Module26
- Trimmer28
- BST4000-1 Belt Stacker Module30
  - BST4000-1 Principle of Operation31
1 Basics33
Turning on / off the Main Power33
- RCT, Booklet Maker, Bookfold Module, Trimmer & BST Module33
Change Staple Cartridges and Check Stapler34
- Change Left/Right Staple Cartridge(S)34
- Check Left/Right Stapler35
Cover Feeder35
- Loading Covers35
Emptying the Trim Waste bin36
Belt Stacker37
- Setting up Belt Stacker for Right-Angled Mode37
- Setting up Belt Stacker for Straight Mode38
2 Making Booklets39
Guided Start39
- Guided Start, Step by Step39
Changing Settings42
- General Procedure42
Basic Settings42
- Input Sheet Size42
- Finished Booklet Size43
  - Auto Trimming43
  - Custom Booklet Size44
Customizing Settings45
- Staple45
  - Selecting Stapling on or off45
  - Adjusting Staple Position45
- Fold Position46
  - Adjusting Fold Position46
- Cover46
- Bookfold48
  - General48
  - Selecting Bookfold Pressure Setting49
- Crease50
  - Crease Mode50
  - Crease Position50
Fine-Tuning Booklet Appearance51
- Set Registration (Fine Adjustment)51
- Bleed Trimmer - Asymmetric Side Trim52
- Bleed Trimmer - Cover Adjust52
Hand-Feeding53
- Hand Feed Mode53
3 Tools55
- The Tools Screen55
- Stacker Full Detection55
- Units55
- Software Version56
- Paper Path Light56
- Language56
- Service Mode57
- Fold Delay57
- Sheet Feeder57
- Auto Rotate58
- Bookfold Offset58
4 Jobs59
Handling Jobs59
- Saving a Job59
- Opening and Handling Stored Jobs60
5 Clearing Misfeed(S)61
- General61
RCT Module62
- Clearing Misfeed(S)62
- Infeed "A" Area and Exit "D" Area62
  - Registration and Creaser Area63
Booklet Maker64
- Clearing Misfeed(S)64
Cover Feeder67
- Clearing Misfeed(S) in Vertical Transport Area67
Bookfold Module68
- Clearing Misfeed(S)68
  - Inside the Bookfold Module68
Trimmer69
- Clearing Misfeed(S)69
  - Clearing Misfeed in Input Area69
  - Clearing Misfeed in Exit Area70
Belt Stacker71
- Clearing Misfeed(S)71
  - Clearing Misfeed on Belt Stacker71
6 Troubleshooting73
Fault Codes73
- General73
- RCT Fault Codes73
- Booklet Maker Fault Codes74
- Cover Feeder Fault Codes75
- Bookfold Module Fault Codes76
- Trimmer Fault Codes77
- Belt Stacker Fault Codes77
- General Fault Codes78
7 Remarks79
Do's and Don'ts79
Where to Put Your Machine80
- Machine Environment80
- Power Connection80
- Access to Machine81
Maintaining Your Machines82
- Cover Feeder82
  - Cleaning Feed Rollers and Paper Separator Pad82
- Bookfold Module83
  - Cleaning Feed Belts83
  - Pressure Springs84
- RCT Module85
Best Practices for the BLM 35/50 System93
Limitations of the BLM 35/50 System94
8 Specification97
Machine Specifications97
- Rotate Crease Trim Module (Option)97
- Booklet Maker98
- Cover Feeder Module99
- Trimmer Module99
- Bookfold Module100
- BST4000-1 Belt Stacker Module100
- System Set Size Guide101
- Cables, Plugs and Jumpers105
Index106

Plockmatic BLM 50 - Page 14

Table of Contents

Related product manuals