Ricoh G104 - Page 391

Service Mode Table
SM 5-11 G160/G161
G160/G161
 Adjusts the leading edge registration. This SP changes the registration
clutch operation timing for each mode.
 A +ve value sets the registration start timing earlier.
 A –ve value sets the registration start timing later. The value of the
normal paper in RS is the standard value. The values of papers other
than normal are added to the value of the normal paper in RS.
1001 001 Tray 1: Normal: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 002 Tray 1: Normal: RS *EGB
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 003 Tray 1: Thick *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 004 Tray 1: OHP *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 005 Tray 2: Normal: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 006 Tray 2: Normal: RS *EGB
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 007 Tray 2: Thick *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 008 Tray 2: OHP *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 009 Tray 3: Normal: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 010 Tray 3: Normal: RS *EGB
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 011 Tray 3: Thick *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 012 Tray 3: OHP *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 013 By-pass: N: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 014 By-pass: N: RS *EGB
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 015 By-pass: Thick *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 016 By-pass: OHP *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 017 Duplex: Normal: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 018 Duplex: Normal: RS *EGB
[-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 019 Duplex: Thick *EGB
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 020 Duplex: N2: LS *EGB
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 021 Duplex: N2: RS *EGB
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 022 Tray 1: Normal 2: LS *EGB
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 023 Tray 1: Normal 2: RS *EGB
[-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 024 Tray 1: Thick 2 *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 025 Tray 1: Thin: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 026 Tray 1: Thin: RS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 027 Tray 1: Special *EGB
[-10.0 to 10.0 / 1.5 / 0.1 mm/step]
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA