Remote Control - Commands
NRP2
219User Manual 1173.9140.02 ─ 07
Deactivates trace 2. In contrast to trace 1 which is always active, trace 2 can be deacti-
vated. Trace 2 is associated with CALCulate5..8 and therefore, also with CONFig-
ure5...8 (see also chapter 6.5, "CALCulate (Configuration of Calculate Blocks)",
on page 224).
Usage: Event
CONFigure<[1]..8>:STATistics:CCDF
CONFigure<[1]..8>:STATistics:PDF
(<statistics_size>), <capture_time>
[,<source_list>]
CONFigure commands for measurement mode Statistics.
6.4.7 Fetch commands
This chapter lists all FETCh commands. For a description of the command syntax, the
calculation functions and the parameter list see chapter 6.4.3, "Syntactical Structure of
High-Level Measurement Commands ", on page 212,
chapter 6.4.5, "Calculation func-
tions - High level commands", on page 215, and chapter 6.4.4, "Parameter list descrip-
tion", on page 212.
FETCh<[1]..8>[:SCALar][:POWer][:AVG]
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:RELative
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence:RELative
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:SUM
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:SUM:RELative
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:RATio
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:RATio:RELative
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:SWR
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:REFLection
FETCh<[1]..8>[:SCALar][:POWer][:AVG]:RLOSs [<expected_value>[,<resolution>]]
[,<source_list>]
FETCh commands for measurement mode ContAv.
FETCh<[1]..8>[:SCALar][:POWer]:TSLot
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:RELative
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:DIFFerence
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:DIFFerence:RELative
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:SUM
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:SUM:RELative
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:RATio
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:RATio:RELative
FETCh<[1]..8>[:SCALar][:POWer]:TSLot:SWR
High-Level Measurement Commands (CONFigure, MEASure, READ and FETCh)
北京海洋兴业科技股份有限公司（证券代码：839145）
To Next Page
Loading...
