EasyManua.ls Logo

Rohde & Schwarz NRP2 - Page 403

Rohde & Schwarz NRP2
419 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Annex
NRP2
402User Manual 1173.9140.02 ─ 07
E4418B/E4419B command Compatibility information
SENSe
:AVERage:
COUNt:AUTO:
SDETect
:DETector:
FUNCtion
:MRATe
:SPEed
:V2P
Is not implemented in the R&S NRP2.
SENSe[1|2]:CORRection
:CSET[1]|CSET2[:SELect]
and
SENSe[1|2]:CORRection
:CSET[1]|CSET2:STATe
The R&S NRP2 does not recognize any tables with frequency-
dependent calibration values since the sensors have to be calibrated
only once in production. For this reason, there is no compliance with
CSET1. Tables with frequency-dependent offset correction values
can be defined and addressed via :CSET2 (Agilent and R&S NRP2)
or :FDOTable
(R&S NRP2 only).
SENSe[1|2]:
CORRection:
GAIN[1]?
Has the same effect as SENSe[1..2]:
CORRection:CFACtor?
SENSe[1|2]:CORRection:
GAIN2[?]
Has the same effect as SENSe[1..2]:CORRection:OFFSet[?].
With :GAIN2, no unit may be specified. Unit 1 is valid.
SENSe[1|2]:CORRection:
LOSS2[?]
Corresponds to the reciprocal of
SENSe[1..2]:
CORRection:
OFFSet[?]. With :LOSS2, no unit
may be specified. Unit 1 is valid.
SENSe[1|2]:CORRection:
GAIN3[?]
Has the same effect as SENSe[1..2]:CORRection:
DCYCle[?].
With :GAIN3, no unit may be specified. Unit 1 is valid.
SENSe[1|2]:CORRection:
GAIN4?
Has the same effect as
SENSe[1..2]:
CORRection:
FDOFfset[:INPut][:
MAGNitude]?
SENSe:SWEep:OFFSet:TIME[?]
Is implemented in the R&S NRP2 and has the same effect as
SENSe:TGATe:OFFSet:TIME[?]
SENSe:SWEep:TIME[?]
Is implemented in the R&S NRP2 and has the same effect as
SENSe:TGATe:TIME[?]
SYSTem
:COMMunicate:SERial
:HELP:HEADers?
:LOCal
:REMote
:RINTerface
:RWLock
Is not implemented in the R&S NRP2.
TRACe:STATe
Is not implemented in the R&S NRP2.
TRACe:DATA?
Is not implemented in the R&S NRP2 in this form. Data of the trace
mode can only be queried via the high-level commands (FETCh?,
READ?
, MEAS?) and CALC:DATA?.
TRACe:UNIT?
The UNIT node is only globally available in the R&S NRP2 and
affects all measurement results (including trace data) and the unit-
less command parameters of the commands CALC:
LIM:LOW
,
CALC:LIM:UPP, DISP:MET|:ANAL:LOW, DISP:MET|:ANAL:UPP,
OUTP:REC:LIM:LOW and OUTP:REC:LIM:UPP.
Compatibility Information
北京海洋兴业科技股份有限公司(证券代码:839145)
电话:010-62176775
网址:www.hyxyyq.com

Table of Contents

Related product manuals