Roland BK-9 - Delete

Rhythm Composer
110
Right Display
1. Use the dial to edit the following parameters.
Parameter Setting Explanation
Track
ADrums~Acc6,
ALL
Allows you to select the track you
wish to edit. You can also select “ALL”
here, in which case the operation
applies to all tracks.
Mode Major, Minor, 7th
Allows you to select the Mode to be
edited.
Division
Intro 1~4, Main
1~4, Fill Dwn 1~3,
Fill Up 1~3, End
1~4
Use this parameter to select the
Division you want to edit.
From Bar
1~[last measure
of the track or
pattern]
Refers to the rst measure to be
edited. By default, the “From” value is
set to the beginning of the selected
track(s).
From Beat
1~[number of
beats per bar]
Species the beat position. The
number of selectable beats depends
on the selected time signature.
From CPT 0~119
Refers to the starting CPT position.
“CPT” is short for “Clock Pulse Time”,
the smallest unit used by the BK-9.
(There are 120 CPTs to every beat of
a 4/4 bar.) Change this setting only if
your edit operation should start after
the selected beat.
To Bar
1~[last measure
of the track or
pattern]
This is where you specify the last
measure to be edited. By default, the
“To” position is set to the last event of
the selected track (or the last event
of the longest track when you select
“All”).
To Beat
1~[number of
beats per bar]
Species the beat position.
The number of selectable beats
depends on the selected time
signature.
To CPT 0~119
Refers to the last clock that should be
aected by the edit operation.
Change this setting only if your edit
operation should not end exactly on
the selected beat.
Parameter Setting Explanation
Data Type
(select the
data to be
edited)
ALL All parameters listed below.
Note Only note messages.
Modulation
CC01 messages usually used for add-
ing vibrato (i.e. use of the BENDER/
MODULATION lever).
PanPot
CC10 messages that specify the
stereo position.
Expression
CC11 messages that are used for
temporary volume changes.
Reverb
Reverb Send messages (how strongly
the part should be processed by the
reverb eect).
Chorus
Chorus Send messages (how strongly
the part should be processed by the
chorus eect).
Program Change
Program change messages, used to
select sounds or Drum Sets.
NOTE
By deleting program change
messages you also dispose of the
related CC00 and CC32 (bank select)
messages.
P.Bender:
Pitch Bend data (i.e. use of the
BENDER/MODULATION lever).
From Note 0 C-~127 G9
This parameter is only displayed
if “Data Type” (see above) is set to
“Note”. It allows you to set the note
(or lower limit of the note range)
to be modied within the specied
“From/To” time range.
To Note 0 C-~127 G9
This parameter allows you to set
the upper limit of the note range
to be modied within the specied
“From/To” time range.
2. Press the [WRITE] button (its indicator ashes) to conrm
your settings and edit the data.
The display briey conrms the operation and then returns to the
current Composer page.
Delete
Unlike the “Erase” function, “Delete” not only erases the data but
also the measures, beats and/or CPT units, so that all data that lie
behind the “To” position are shifted towards the beginning of the
track(s). You cannot choose the data type to be erased.
Right Display
1. Use the dial to edit the following parameters.
Parameter Setting Explanation
Track
ADrums~Acc6,
ALL
Allows you to select the track you wish to
edit. You can also select “ALL” here, in which
case the operation applies to all tracks.
Mode Major, Minor, 7th Allows you to select the Mode to be edited.