Roland BK-9 - Erase; Delete

Working with the 16-Track Sequencer
86
Parameter Setting Explanation
From Bar
For details information see p. 85.
From Beat
From Cpt
To Bar
To Beat
To Cpt
Resolution
1/4, 1/8, 1/8T,
1/16, 1/16T, 1/32,
1/32T, 1/64
This parameter sets the resolution of
the Quantize function. Be sure to always
select the value of the shortest note you
recorded. Otherwise, your part no longer
sounds the way you played it, because
shorter notes are shifted to the wrong
positions.
Strength 0%~100%
Use this parameter to specify how
precise the timing correction should
be. “0%” means that the selected
“Resolution” value is not applied (“0%
correction”), while “100%” means that all
notes are shifted to the mathematically
correct positions.
Maybe rst try values between “50%”
and “85%” to preserve at least part
of the original feel. If the result is not
acceptable, repeat the operation with
the same or a higher value.
From Note C-~G9
This parameter allows you to set the
note (or lower limit of the note range)
to be modied within the specied
“From”/“To” time range.
To Note C-~G9
This parameter allows you to set
the upper limit of the note range
to be modied within the specied
“From”/“To” time range.
ERASE
ERASE allows you to selectively delete data either within a specied
range of measures, beats or clocks or from the entire track(s). When
“Data Type” is set to “ALL”, ERASE substitutes the required number of
rests for the data you delete, so that you end up with the equivalent
number of blank measures. If you also want to eliminate the
measures themselves, use DELETE (see below).
Erase NOTE From 2.1.0 To 4.1.0
Left Display Right Display
Parameter Setting Explanation
Track All, Trk 1~ Trk 16
Allows you to select the track you wish
to edit. You can also select “ALL” here,
in which case the operation applies to
all tracks.
Parameter Setting Explanation
From Bar
For details information see p. 85.
From Beat
From Cpt
To Bar
To Beat
To Cpt
Data Type
ALL, Note,
P.Bender, Control
Change, Program
Change, NRPN,
RPN, CAF,
Allows you to select the data to be
erased.
From Note C-~G9
This parameter allows you to set the
note (or lower limit of the note range)
to be modied within the specied
“From”/“To” time range.
To Note C-~G9
This parameter allows you to set
the upper limit of the note range
to be modied within the specied
“From”/“To” time range.
If “Data Type” (see above) is set to “Note” the following parameters
are displayed also.
Parameter Setting Explanation
From Note C-~G9
This parameter allows you to set the
note (or lower limit of the note range)
to be modied within the specied
“From”/“To” time range.
To Note C-~G9
This parameter allows you to set
the upper limit of the note range
to be modied within the specied
“From”/“To” time range.
If “Data Type” (see above) is set to “Control Change” the following
parameters are displayed also.
Parameter Setting Explanation
From CC 0~127
It allows you to set the lower limit of
the control change numbers or values
to be modied within the specied
“From”/“To” time range.
To CC 0~127
This parameter allows you to set the
upper limit of the control change
numbers or values to be modied within
the specied “From”/“To” time range.
DELETE
Unlike the ERASE function, DELETE not only erases the data but also
the measures, beats and/or CPT units, so that all data that lie behind
the TO position are shifted towards the beginning of the track(s).
For this reason, you cannot choose the data type to be erased.
Delete From 2.1.0 To 4.1.0