Roland BK-9 - Rx Ch; Rx Event; Rx Limit Low;Limit High; Rx Shift

MIDI
153
Tx Shift
This parameter allows you to transpose the note messages before
they are transmitted to an external MIDI instrument or computer.
The maximum possible transposition is four octaves up (+48) or
down (–48).
Each step represents a semi-tone.
Parameter Setting
Tx Shift –48~0~+48
Tx Local
This is where you can disconnect the part from the internal sound
source (“O”) – or re-establish that connection (“On”).
Parameter Setting
Tx Local O, On
Tx Event
The “TX Event” section provides a number of lters that allow you
to specify whether the messages in question should be transmitted
(On) or not (O).
Parameter Setting Explanation
Program Change O, On
Select “On” to transmit program change and
bank select (CC00, CC32) messages.
Pitch Bender O, On Select “On” to transmit Pitch Bend messages.
Modulation O, On
Select “On” to transmit Modulation messages
(CC01).
Volume O, On
Select “On” to transmit Volume messages
(CC07).
Panpot O, On
Select “On” to transmit Panpot messages
(CC10).
Expression O, On
Select “On” to transmit Expression messages
(CC11).
Reverb O, On
Select “On” to transmit Reverb messages
(CC91).
Chorus O, On
Select “On” to transmit Chorus messages
(CC93).
Hold* O, On Select “On” to receive Hold messages (CC64).
Sostenuto* O, On
Select “On” to receive Sostenuto messages
(CC66).
Soft* O, On Select “On” to receive Soft messages (CC67).
Caf* O, On Select “On” to receive Caf Channel aftertouch.
RPN* O, On
Select “On” to receive Registered parameter
number messages (CC100/101).
NRPN* O, On
Select “On” to receive Nonregistered
parameter number messages (CC98/99).
System
Exclusive*
O, On
Select “On” to receive System Exclusive
messages.
Other CC* O, On
General purpose controller and others CC not
listed above.
Select All O, On
Select “On” to transmit all MIDI message listed
above.
* This parameter is available for Tone and Song parts only.
Rx
Select “On” if you want the selected part to receive MIDI data.
Parameter Setting
Rx O, On
Rx Ch
Allows you to assign a MIDI receive channel to the selected part.
Parameter Setting
Rx Ch 1~16
Rx Shift
This parameter allows you to transpose the note messages received
from an external MIDI instrument or computer. The maximum
possible transposition is four octaves up (+48) or down (–48). Each
step represents a semi-tone.
Parameter Setting
Rx Shift –48~0~+48
Rx Limit Low/Limit High
“Limit Low” and “Limit High” allow you to set the note range to be
received. If not all note messages received on a given MIDI channel
should be played by the selected BK-9 part, narrow down the range.
Parameter Setting
Rx Limit Low
C–~G9
Rx Limit High
NOTE
The “Limit Low” value cannot be higher than the “Limit High”
value (and vice versa).
Rx Event
The “Rx Event” section provides a number of lters that allow you to
specify whether the messages in question should be received (On)
or not (O).
Parameter Setting Explanation
Program Change O, On
Select “On” to receive program change and
bank select (CC00, CC32) messages.
Pitch Bender O, On Select “On” to receive Pitch Bend messages
Modulation O, On
Select “On” to receive Modulation messages
(CC01).
Volume O, On
Select “On” to receive Volume messages
(CC07).
Panpot O, On
Select “On” to receive Panpot messages
(CC10).
Expression O, On
Select “On” to receive Expression messages
(CC11).
Reverb O, On
Select “On” to receive Reverb messages
(CC91).
Chorus O, On
Select “On” to receive Chorus messages
(CC93).
Hold* O, On Select “On” to receive Hold messages (CC64).
Sostenuto* O, On
Select “On” to receive Sostenuto messages
(CC66).
Soft* O, On Select “On” to receive Soft messages (CC67).
Caf* O, On Select “On” to receive Caf Channel aftertouch.
RPN* O, On
Select “On” to receive Registered parameter
number messages (CC100/101).
NRPN* O, On
Select “On” to receive Nonregistered
parameter number messages (CC98/99).
System
Exclusive*
O, On
Select “On” to receive System Exclusive
messages.
Other CC* O, On
General purpose controller and others CC not
listed above.