Roland JD-XA - (4 Tap Pan Delay); 38: Mlt Tap Dly (Multi Tap Delay)

39
Eects
37: 4Tap Delay
(4 Tap Pan Delay)
This eect has four delays.
L in
R in
L out
R out
Quadruple Tap Delay
Balance W
Balance D
Balance W
Balance D
Delay 1
Delay 2
Delay 3
Delay 4
Feedback
1
2 3
4
L
R
Parameter Value Explanation
Dly 1–4 Sync
(Delay 1–4 Sync)
msec, NOTE
msec: The Dly 1–4 Time value is
specied in msec.
NOTE: The Dly 1–4 Time value is
specied as a note value.
Dly 1–4 Time/
Note
(Delay 1–4 Time/Note)
0–2600 ms, note
Adjusts the time from the direct
sound until delay sounds 1–4 are
heard
Dly 1 Fback #
(Delay 1 Feedback)
-98–+98%
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative (-) values invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect is
ltered out.
If you do not want to lter out any
high frequencies, set this parameter
to BYPASS.
Dly 1–4 Level
(Delay 1–4 Level)
0–127 Volume of each delay
Low Gain -15–+15 dB Amount of low-range boost/cut
High Gain -15–+15 dB Amount of high-range boost/cut
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output volume
38: Mlt Tap Dly
(Multi Tap Delay)
This eect provides four delays. Each of the Delay Time parameters
can be set to a note length based on the selected tempo. You can
also set the panning and level of each delay sound.
L in
R in
L out
R out
Multi Tap Delay
Balance W
Balance D
Balance W
Balance D
Delay 1
Delay 3
Delay 4
Delay 2
Feed
back
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Dly 1–4 Sync
(Delay 1–4 Sync)
msec, NOTE
msec: The Dly 1–4 Time value is
specied in msec.
NOTE: The Dly 1–4 Time value is
specied as a note value.
Dly 1–4 Time/
NOTE
(Delay 1–4 Time/Note)
0–2600 ms, note
Adjusts the time from the direct
sound until delay sounds 1–4 are
heard
Dly 1 Fback #
(Delay 1 Feedback)
-98–+98%
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative (-) values invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect is
ltered out.
If you do not want to lter out any
high frequencies, set this parameter
to BYPASS.
Delay 1–4 Pan L64–63R Stereo location of each delay
Dly 1–4 Level
(Delay 1–4 Level)
0–127 Volume of each delay
Low Gain -15–+15 dB Amount of low-range boost/cut
High Gain -15–+15 dB Amount of high-range boost/cut
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the eect sound (W)
Level 0–127 Output volume