Roland JD-XA - JD-XA Utility Functions Overview; USB Memory Formatting

18
Eects
Part EQ Edit
Menu
[Shift] +Cursor [
K
] [
J
]
Parameter
Cursor [
K
] [
J
]
Value
Value [-] [+]
Explanation
PART EQ
(Part Equalizer)
Switch
(Part Equalizer Switch)
OFF, ON EQ for each part on/o setting
Low Freq
(Part Equalizer Low Frequency)
16 Hz, 20 Hz, 25 Hz, 31
Hz, 40 Hz, 50 Hz, 63 Hz,
80 Hz, 100 Hz, 125 Hz,
160 Hz, 200 Hz, 250 Hz,
315 Hz, 400 Hz, 500 Hz,
630 Hz, 800 Hz
Frequency of the low range.
Low Gain
(Part Equalizer Low Gain)
-15 dB–0–+15 dB Gain of the low frequency range
Mid Freq
(Part Equalizer Mid Frequency)
16 Hz, 20 Hz, 25 Hz, 31
Hz, 40 Hz, 50 Hz, 63 Hz,
80 Hz, 100 Hz, 125 Hz,
160 Hz, 200 Hz, 250
Hz, 315 Hz, 400 Hz, 500
Hz, 630 Hz, 800 Hz,
1000 Hz, 1250 Hz, 1600
Hz, 2000 Hz, 2500 Hz,
3150 Hz, 4000 Hz, 5000
Hz, 6300 Hz, 8000 Hz,
10000 Hz, 12500 Hz,
16000 Hz
Frequency of the middle range
Mid Gain
(Part Equalizer Mid Gain)
-15 dB–0–+15 dB Gain of the middle frequency range
Q
(Part Equalizer Mid Q)
0.5, 1.0, 2.0, 4.0, 8.0
Width of the middle frequency range
Set a higher value for Q to narrow the range to be aected.
High Freq
(Part Equalizer High Frequency)
630 Hz, , 800 Hz, 1000
Hz, 1250 Hz, 1600 Hz,
2000 Hz, 2500 Hz, 3150
Hz, 4000 Hz, 5000 Hz,
6300 Hz, 8000 Hz, 10000
Hz, 12500 Hz, 16000 Hz
Frequency of the high range
High Gain
(Part Equalizer High Gain)
-15 dB–0–+15 dB Gain of the high frequency range
TFX Edit
Menu
[Shift] +Cursor [
K
] [
J
]
Parameter
Cursor [
K
] [
J
]
Value
Value [-] [+]
Explanation
TFX1
(TFX 1)
TFX2
(TFX 2)
Type
(TFX Type)
00–29
Use this parameter to select from among the 29 available total eect. For details on total eect
parameters, refer to “TFX Parameters” (p. 19).
Ctrl
(TFX Control)
0–127
Globally controls the selected total eect.
Global control means to control multiple parameters simultaneously.
Switch
(TFX Switch)
OFF, ON Species whether total eect will be used (ON) or not used (OFF).
Parameters for each type
& “TFX Parameters” (p. 19)
Edit the parameters for the selected TFX type.
Limit ModeSw
(TFX Limit Mode Switch)
OFF, ON
If you turn Limit Mode on, the eect depth is restricted to prevent feedback or an extremely
high volume.
Parameters that are aected by Limit Mode are indicated by a
symbol (p. 19). This can be
convenient when you’re performing in high-volume conditions at a club or hall.
* This parameter is not shown for types that have no parameters marked by
.
HeadMargin
(TFX Head Margin)
-18 dB, -15 dB, -12 dB,
-9 dB, -6 dB, -3 dB, 0 dB
Simultaneously adjusts the input and output gain of the total eect.
This is convenient when adjusting dynamics-type eects (such as overdrive or compressor) that
produce their eect by varying the volume. For some eects, it may be dicult to notice the
result of this adjustment.