Roland JD-XA - Dist->Cho (Distortion 0 Chorus); Od->Cho (Overdrive 0 Chorus); Od->Dly (Overdrive 0 Delay); Od->Flg (Overdrive 0 Flanger)

42
Eects
45: Od->Cho
(Overdrive 0 Chorus)
L in
R in
Chorus
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
OD Drive #
(Overdrive Drive)
0–127
Degree of distortion
Also changes the volume.
OD Pan #
(Overdrive Pan)
L64–63R
Stereo location of the overdrive
sound
Cho PreDly
(Chorus Pre Delay)
0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
ChorusSync Hz, NOTE
Hz: The Cho Rate value is specied
in Hz.
NOTE: The Cho Rate value is
specied as a note value.
Cho Rate #
(Chorus Rate)
0.05–10.00 Hz,
note
Rate of modulation
Chorus Depth 0–127 Depth of modulation
Cho Bal #
(Chorus Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
Level 0–127 Output volume
46: Od->Flg
(Overdrive 0 Flanger)
L in
R in
Flanger
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Parameter Value Explanation
OD Drive #
(Overdrive Drive)
0–127
Degree of distortion
Also changes the volume.
OD Pan #
(Overdrive Pan)
L64–63R
Stereo location of the overdrive
sound
Flg PreDly
(Flanger Pre Delay)
0.0–100.0 ms
Adjusts the delay time from the
direct sound until the anger sound
is heard.
Flg Sync
(Flanger Sync)
Hz, NOTE
Hz: The Flg Rate value is specied
in Hz.
NOTE: The Flg Rate value is specied
as a note value.
Flg Rate #
(Flanger Rate)
0.05–10.00 Hz,
note
Rate of modulation
Flg Depth
(Flanger Depth)
0–127 Depth of modulation
FlgFeedback #
(Flanger Feedback)
-98–+98%
Adjusts the proportion of the anger
sound that is fed back into the
eect.
Negative (-) values invert the phase.
Flg Bal #
(Flanger Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the anger (W) and the
sound that is not sent through the
anger (D).
Level 0–127 Output volume
47: Od->Dly
(Overdrive 0 Delay)
L in
R in
Delay
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Parameter Value Explanation
OD Drive #
(Overdrive)
0–127
Degree of distortion
Also changes the volume.
OD Pan #
(Overdrive Pan)
L64–63R
Stereo location of the overdrive
sound
Delay Sync msec, Note
msec: The Dly Time/Note value is
specied in msec.
NOTE: The Dly Time/Note value is
specied as a note value.
Dly Time/Note
(Delay Time/Note)
0–2600 ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
DlyFeedback #
(Delay Feedback)
-98–+98%
Adjusts the proportion of the delay
sound that is fed back into the
eect.
Negative (-) values invert the phase.
D HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect will
be cut.
If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Dly Bal #
(Delay Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D).
Level 0–127 Output volume
48: Dist->Cho
(Distortion 0 Chorus)
L in
R in
Chorus
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Dist Drive #
(Distortion Drive)
0–127
Degree of distortion
Also changes the volume.
Dist Pan #
(Distortion Pan)
L64–63R
Stereo location of the distortion
sound
Cho PreDly
(Chorus Pre Delay)
0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
ChorusSync Hz, NOTE
Hz: The Cho Rate value is specied
in Hz.
NOTE: The Cho Rate value is
specied as a note value.
Cho Rate #
(Chorus Rate)
0.05–10.00 Hz,
note
Rate of modulation
Chorus Depth 0–127 Depth of modulation
Cho Bal #
(Chorus Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
Level 0–127 Output volume