EasyManua.ls Logo

Roland JD-XA - OD;DS->Awah (OD;DS 0 Auto Wah); OD;DS->Twah (OD;DS 0 Touch Wah)

Roland JD-XA
76 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
44
Eects
51: OD/DS->TWah
(OD/DS 0 Touch Wah)
Amp
Simulator
2-Band
EQ
L in
R in
Overdrive/
Distortion
L out
R out
Touch
Wah
Parameter Value Explanation
Drive Switch OFF, ON Turns overdrive/distortion on/o
Type
OVERDRIVE,
DISTORTION
Type of distortion
Drive # 0–127
Degree of distortion
Also changes the volume.
Tone # 0–127 Sound quality of the eect
Amp Switch OFF, ON Turns the Amp Simulator on/o.
AmpType
SMALL, BUILT-IN,
2-STACK, 3-STACK
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Touch Wah Sw
(Touch Wah Switch)
OFF, ON Wah on/o
TWah FilterType
(Touch Wah Filter Type)
LPF, BPF
Type of lter
LPF: Produces a wah eect in a
broad frequency range.
BPF: Produces a wah eect in a
narrow frequency range.
TWah Polar
(Touch Wah Polarity)
DOWN, UP
Sets the direction in which the
frequency will change when the
touch-wah lter is modulated.
UP: The lter will change toward a
higher frequency.
DOWN: The lter will change toward
a lower frequency.
TWah Sens #
(Touch Wah Sens)
0–127
Sensitivity with which the lter is
modied
TWah Manual #
(Touch Wah Manual)
0–127
Center frequency at which the wah
eect is applied
TWah Peak #
(Touch Wah Peak)
0–127
Width of the frequency region at
which the wah eect is applied.
Increasing this value will make the
frequency region narrower.
TWah Bal #
(Touch Wah Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the wah (W) and the sound
that is not sent through the wah (D).
Low Gain -15–+15 dB Amount of low-range boost/cut
High Gain -15–+15 dB Amount of high-range boost/cut
Level 0–127 Output volume
52: OD/DS->AWah
(OD/DS 0 Auto Wah)
Amp
Simulator
2-Band
EQ
L in
R in
Overdrive/
Distortion
L out
R out
Auto
Wah
Parameter Value Explanation
Drive Switch OFF, ON Turns overdrive/distortion on/o
Type
OVERDRIVE,
DISTORTION
Type of distortion
Drive # 0–127
Degree of distortion
Also changes the volume.
Tone # 0–127 Sound quality of the eect
Amp Switch OFF, ON Turns the Amp Simulator on/o.
AmpType
SMALL, BUILT-IN,
2-STACK, 3-STACK
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Auto Wah Sw OFF, ON Wah on/o
AWah FltType
(Auto Wah Filter Type)
LPF, BPF
Type of lter
LPF: Produces a wah eect in a
broad frequency range.
BPF: Produces a wah eect in a
narrow frequency range.
AWah Manual #
(Auto Wah Manual)
0–127
Center frequency at which the wah
eect is applied
AWah Peak #
(Auto Wah Peak)
0–127
Width of the frequency region at
which the wah eect is applied
Increasing this value will make the
frequency region narrower.
AWah Sync
(Auto Wah Sync)
Hz, NOTE
Hz: The AWah Rate value is specied
in Hz.
NOTE: The AWah Rate value is
specied as a note value.
AWah Rate #
(Auto Wah Rate)
0.05–10.00 Hz,
note
Rate at which the wah eect is
modulated
AWah Depth #
(Auto Wah Depth)
0–127
Depth at which the wah eect is
modulated
AWah Bal #
(Auto Wah Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the wah (W) and the sound
that is not sent through the wah (D).
Low Gain -15–+15 dB Amount of low-range boost/cut
High Gain -15–+15 dB Amount of high-range boost/cut
Level 0–127 Output volume

Table of Contents

Other manuals for Roland JD-XA

Related product manuals