Roland JD-XA - Eh->Cho (Enhancer 0 Chorus); Eh->Flg (Enhancer 0 Flanger); EP->Dly (EP Amp Sim 0 Delay)

51
Eects
61: EP->Dly
(EP Amp Sim 0 Delay)
Balance W
Balance D
L in
R in
L out
R out
EP Amp
Speaker
Feedback
Time Ctrl
Delay
Balance W
Balance D
Parameter Value Explanation
Type
OLDCASE,
NEWCASE,
WURLY
Type of amp
OLDCASE: a standard electric piano
sound of the early 70s
NEWCASE: a standard electric piano
sound of the late 70s and early 80s
WURLY: a standard electric piano
sound of the 60s
Bass # -50–+50 Amount of low-frequency boost/cut
Treble # -50–+50
Amount of high-frequency boost/
cut
Delay Switch # OFF, ON Delay on/o
Delay Sync msec, NOTE
msec: The Dly Time/Note value is
specied in msec.
NOTE: The Dly Time/Note value is
specied as a note value.
Dly Time/Note #
(Delay Time/Note)
0–1300 ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
Delay Accel
(Delay Acceleration)
0–15
Speed at which the current delay
time changes to the specied delay
time when you change the delay
time.
The rate of change for the Delay
Time directly aects the rate of pitch
change.
DlyFeedback #
(Delay Feedback)
-98–+98%
Adjusts the proportion of the delay
sound that is fed back into the
eect.
Negative (-) values invert the phase.
D HF Damp
(Delay HF Damp)
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Dly Bal #
(Delay Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through the
delay (D).
Sp Type
(Speaker Type)
LINE, OLD, NEW,
WURLY, TWIN
Type of speaker
* If LINE is selected, the sound will
not be sent through the speaker
simulation.
OD Switch
(Overdrive Switch)
OFF, ON Overdrive on/o
OD Gain
(Overdrive Gain)
0–127 Overdrive input level
OD Drive
(Overdrive Drive)
0–127 Degree of distortion
Level 0–127 Output volume
62: Eh->Cho
(Enhancer 0 Chorus)
Chorus
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
EnhancerSens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127
Level of the overtones generated by
the enhancer
Cho PreDly
(Chorus Pre Delay)
0.0–100.0 ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
ChorusSync
(Chorus Sync)
Hz, NOTE
Hz: The Cho Rate value is specied
in Hz.
NOTE: The Cho Rate value is
specied as a note value.
Cho Rate #
(Chorus Rate)
0.05–10.00 Hz,
note
Rate of modulation
Chorus Depth 0–127 Depth of modulation
Cho Bal #
(Chorus Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
Level 0–127 Output volume
63: Eh->Flg
(Enhancer 0 Flanger)
Feedback
Flanger
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
EnhancerSens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127
Level of the overtones generated by
the enhancer
Flg PreDly
(Flanger Pre Delay)
0.0–100.0 ms
Adjusts the delay time from the
direct sound until the anger sound
is heard.
Flg Sync
(Flanger Sync)
Hz, NOTE
Hz: The Cho Rate value is specied
in Hz.
NOTE: The Cho Rate value is
specied as a note value.
Flg Rate #
(Flanger Rate)
0.05–10.00 Hz,
note
Rate of modulation
Flg Depth
(Flanger Depth)
0–127 Depth of modulation
FlgFeedback #
(Flanger Feedback)
-98–+98%
Adjusts the proportion of the anger
sound that is fed back into the
eect.
Negative (-) values invert the phase.
Flg Bal #
(Flanger Balance)
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is sent
through the anger (W) and the
sound that is not sent through the
anger (D).
Level 0–127 Output volume