MX3500N SIMULATION 7 – 33
26-18
Purpose
Setting
Function (Purpose)
Used to set the toner save mode.
Section
—
Item
—
Operation/Procedure
1) Use [↑] and [↓] buttons to select an item.
The set value is highlighted and the value is displayed in the
setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
26-30
Purpose
Setting
Function (Purpose)
Used to set allow/inhibit of HL slow-up con-
trol (CE mark support control).
Section
—
Item
Specifications (Operation mode (common
operation))
Operation/Procedure
1) When the machine enters the simulation, the following screen
is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
NOTE: Even though the control is allowed, the CE mark support
control may not be executed depending on the power fre-
quency, etc.
<Initial value and set value linked with the destination>
26-35
Purpose
Setting
Function (Purpose)
Used to set the trouble memory saving pro-
cedure.
Section
—
Item
—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
Item Display Content
Setting
range
Default
value
ACOPY
(1:YES 0:NO)
0 Copy toner save mode
is allowed
0 to 1 0
1 Copy toner save mode
is inhibited.
BPRINTER
(1:YES 0:NO)
0 Printer toner save
mode is allowed.
0 to 1 0
1 Printer toner save
mode is inhibited.
0
A:
A:1
TRIAL MODE (0:YES 1:NO)
SIMULATION NO.26-10
NETWORK SCANNER TRIAL MODE SETUP
1
[0~ 1]
OK
TEST
CLOSE
0
:
A㧦 0
B㧦 0
㧧 COPY(1:YES 0:NO)
㧧 PRINTER(1:YES 0:NO)
SIMULATION
NO.26
㧙
18
TONER SAVE MODE SETUP
0
㨇 0㨪 1 㨉
OK
TEST
CLOSE
Item Display Content
Setting
range
Default value
A (0:YES 1:NO) 0 CE mark
control allowed
0 to 1 Refer to <Initial
value and set
value linked with
the destination>.
1CE mark
control inhibited
Destination Setting value
U.S.A 1 (CE not supported)
CANADA 1 (CE not supported)
INCH 1 (CE not supported)
JAPAN 1 (CE not supported)
AB_B 1 (CE not supported)
EUROPE 0 (CE supported)
U.K 0 (CE supported)
AUS. 0 (CE supported)
AB_A 0 (CE supported)
CHINA 0 (CE supported)
Item Display Content
Setting
range
Default
value
A(0:ONCE
1:ANY)
0 Only once. If same as the
previous one, it is not saved.
0 to 1 0
1 Any time. Though same as
the previous one, it is saved.