MX-M700N SIMULATION 7 – 10
3-3
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS] key.
(When the punch unit is installed)
(When the saddle unit is installed.
3-10
Purpose
Adjustment
Function (Purpose)
Finisher (AR-F16) adjustment
Section
Finisher
Operation/Procedure
1) Select the number that corresponds to the adjustment item
with 10-key.
2) Press the [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
3-30
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the inserter and the
related circuit.
Section
Inserter
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
1 SL7 Belt wait solenoid
2 SL6 Wait solenoid
3 SL5 Paddle solenoid
4 SL3 Buffer exit port solenoid
5 SL2 Buffer entry port solenoid
6 SL1 Flapper solenoid
7 M10 Tray 2 lift motor
8 M9 Entry port transport motor
9 M8 No. 2 transport motor
10 M7 Oscillation motor
11 M6 Staple motor
12 M5 Tray 1 lift motor
13 M4 Stapler shift motor
14 M3 Alignment motor
15 M2 Paper exit motor
16 M1 No. 1 transport motor
17 M2P Punch side resist motor
18 M1P Punch motor
19 SL4S Transport plate contact solenoid
20 SL2S No. 2 paper deflection plate solenoid
21 SL1S No. 1 paper deflection plate solenoid
22 M8S Paper holding motor
23 M7S Stitch motor: Front
24 M6S Stitch motor: Rear
25 M5S Saddle alignment motor
26 M4S Paper positioning motor
27 M3S Guide motor
28 M2S Paper folding motor
29 M1S Saddle transport motor
Item Setting range
1 Saddle stitch/folding
position adjustment
192 - 208, 1STEP: 0.25 mm
2 Alignment position
adjustment
2 - 18, 1STEP: 0.35 mm
SIMULATION 3-3
FINISHER LOAD TEST.㵘SELECT㵘1-㵘䋬AND PRESS START.
2 㩷
3 Staple binding position
adjustment
68 - 132, 1STEP: 0.152 mm
4 Punch center
adjustment
37 - 63, 1STEP: 0.15mm
5 Punch hole position
adjustment (Paper feed
direction)
35 - 57, 1STEP: 0.26mm
6 Stack tray standby
position adjustment
(Small size)
5 - 35, 1STEP: 1mm
7 Stack tray standby
position adjustment
(Large size)
5 - 35, 1STEP: 1mm
TH_SEN Sub tray pull-out detection
TS_SEN Sub tray storage detection
T_SEN Inserter tray paper size detection
EMP_SEN Inserter tray empty detection
REG_SEN Inserter resist sensor
TIM_SEN Inserter timing sensor detection
JCK_SEN Inserter cover open/close sensor
H_SEN Inserter reverse sensor
HI_SEN Inserter paper exit sensor
HYK_SEN Inserter reverse unit open/close sensor
S_SW Inserter set SW
KC_SEN Base cover open/close sensor
P_ST_SW Inserter start SW
P_MO_SW Inserter staple mode select SW
P_PN_SW Inserter punch select SW
Item Setting range
SIMULATION 3-10
FINISHER SETTING.㵘SELECT㵘1-7䋬AND PRESS START.
1. SADDLE POSITION
2. ALIGNMENT㵘POSITION
3. STAPLE㵘POSITION
4. PUNCH㵘CENTER
5. PUNCH㵘HOLE
6. TRAY WAITING POSITION(S-SIZE)
7. TRAY WAITING POSITION(L-SIZE)
1
SIMULATION 3-30
INSERTER SENSOR CHECK.
TH_SEN TS_SEN T_SEN EMP_SEN
REG_SEN TIM_SEN JCK_SEN H_SEN
HI_SEN HYK_SEN S_SW KC_SEN
P_ST_SW P_MO_SW P_PN_SW
To Next Page
Loading...
