MX-M700N SIMULATION 7 – 11
3-31
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the loads
in the inserter and the related circuits.
Section
Inserter
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS]
key.
3-32
Purpose
Setting (Adjustment)
Function (Purpose)
Inserter paper width detection level setting.
Section
Inserter
Operation/Procedure
1) Select the number corresponding to the adjustment item with
10-key.
2) Press the [START] key.
3) Enter the setting (adjustment) value with 10-key.
4) Press the [START] key.
4
4-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the sen-
sors and detectors in the paper feed sec-
tion (large capacity tray) and the related
circuit.
Section
Paper feed
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
<LCC>
4-3
Purpose
Operation test/Check
Function (Purpose)
Used to check the operations of the loads
in the paper feed section (large capacity
tray) and the related circuit.
Section
Paper feed
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS] key.
<Side LCC>
5
5-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
Section
Operation (Display/Operation key)
Operation/Procedure
The contrast changes every 2sec from the current level to MAX →
MIN → the current level. During this period, each LED is lighted.
1 K_MOT Reverse motor
2 Y_MOT Horizontal transport motor
3 H_MOT Inserter reverse
4 F_SOL Inserter flapper solenoid
5 R_CL Inserter resist clutch
6 P_LED Inserter operation panel upper LED
1 MAX. POSITION Max. position
2 POSITION 1 Adjustment point 1
3 POSITION 2 Adjustment point 2
4 MIN. POSITION Min. width
SIMULATION 3-31
INSERTER LOAD TEST. SELECT 1-6, AND PRESS START.
1. K_MOT 2. Y_MOT 3. H_MOT
4. F_SOL 5. R_CL 6. P_LED
2
1
SIMULATION 3-32
INSERTER TRAY VALUE SETTING. SELECT 1-4, AND PRESS
START.
1. MAX. POSITION : 72
2. POSITION 1 : 380
3. POSITION 2 : 710
4. MIN. POSITION : 804
LTD Transport sensor
LUD Tray upper limit sensor
LLD Tray lower limit sensor
LPED Tray paper presence/empty sensor
LTOD Main unit connection detection sensor
LCD Tray insertion detection
LOSW Upper open/close detection SW
LRE Lift motor encoder sensor
+24VM 24V power monitor
LLSW Upper limit SW
1 LTM LCC transport motor
2 LLM LCC lift motor
3 LPFCL Paper feed clutch
4 LPSL LCC paper feed solenoid
5 LTCL LCC transport clutch
6 LTLSL Tray lock solenoid D
SIMULATION 4-2
LCC SENSOR CHECK.
LTD LUD LLD LPED
LTOD LCD LOSW LRE
+24VM LLSW
SIMULATION 4-3
LCC LOAD TEST. SELECT 1-6, AND PRESS START.
1.LTM 2.LLM
3.LPFCL 4.LPSL
5.LTCL 6.LTLSL
2
㩷SIMULATION 5-1
To Next Page
Loading...
