SICK Advanced Series

Chapter 10 Operating Instructions

CLV490 Bar Code Scanner

Appendix

Documentation additional................................................... 10-85

Download

- Function..................................................................................... 6-5

- Start Download....................................................................... 6-6

E

Electrical installation .................................................................... 5-1

EMC ................................................................................................... 9-2

Enclosure rating (IP) .................................................................... 9-2

Error messages

- Display in the Terminal Emulator ..................................... 8-2

- Function..................................................................................... 3-7

- List (CLV with external parameter memory)................ 8-5

- List (CLV without external parameter memory) ......... 8-2

Error status in the reading result............................................ 8-7

Ethernet...................................................................................... 10-72

Evaluation

- Decoder types ........................................................................ 3-6

- Parameterization.....................................................6-36, 6-37

F

Figures (overview)....................................................................... I-13

Firmware ............................................................................................ I-2

Focus position switching

- Function..................................................................................... 3-8

- Parameterization................................................................. 6-12

- Trigger modes......................................................................... 3-8

G

Glossary ..................................................................................... 10-86

Good Read................................................................................... 6-40

H

Header........................................................................................... 6-56

Heating

- Behavior .............................................................................. 10-40

- Connection cables........................................................... 10-81

- Design.................................................................................. 10-40

- Electrical connection....................................................... 10-41

- Function............................................................................... 10-40

- Power consumption........................................................ 10-41

- Switching on delay........................................................... 10-40

- System requirements........................................................... 3-2

- Temperatur range............................................................ 10-40

Host interface

- Connecting ............................................................................ 5-20

- Data output string............................................................... 6-56

- Default setting...................................................................... 5-20

- Function..................................................................................... 3-6

- Max. cable lengths ............................................................. 5-16

- Monitoring in the Terminal Emulator ........................... 6-55

- Parameterization................................................................. 6-37

- Select hardware.................................................................. 5-21

I

I/O monitor in increment trigger........................................... 6-48

Identical bar codes

- Function of RA, CW values ................................................. 4-6

- Parameterzing the evaluation ........................................ 6-36

- Separation................................................................................ 4-6

IN 0 ... IN 4 switching inputs

- Assignment table................................................................ 5-24

- Caracteristic data................................................................5-24

- Connection.............................................................................5-23

- Function .....................................................................................3-6

- Parameterization..................................................................6-38

Incremental sensor

- Application.................................................................................3-2

- Electrical connecting ..........................................................5-23

- Function .....................................................................................3-9

- Installation..............................................................................4-12

Indicators.......................................................................................3-11

Installation

- Electrical installation..............................................................5-1

- Mounting....................................................................................4-1

- Overview ......................................................................................I-4

Intended use of CLV ....................................................................2-1

Interfaces of CLV

- Functions...................................................................................3-6

- Overview ....................................................................................5-1

- Pin assignment........................................................................5-7

L

Laser radiation

- Laser power .............................................................................2-2

- Laser warning lables (content)..........................................2-2

- Protection class ......................................................................2-2

- Protective circuits, internal..................................................2-3

- Replacing the laser warning labels..................................4-2

- User instructions.....................................................................2-2

- Wave length..............................................................................2-2

Laser timeout

- Function .....................................................................................2-3

- Parameterization..................................................................6-36

LEDs

- Function (CLV with ext. param. memory) ...................3-12

- Function (CLV without ext. param. memory).............3-11

- Parameterization (Result 1(LED "Read Result"))....6-37

- Position.......................................................................................3-5

Line scanner

- Dimensional drawing.............................................................9-4

- Function .....................................................................................3-9

- Quick start.................................................................................6-3

- Technical data .........................................................................9-1

M

Malfunctions

- Diagnosis and remedy .........................................................8-9

- Error messages.......................................................................8-2

Messages (terminal interface)..............................................6-59

Method of operation

- Block diagram..........................................................................3-6

- Description................................................................................3-6

Monitoring host interface

- Function ..................................................................................6-55

- Starting the mode ...............................................................6-55

Mounting

- Accessories..............................................................................4-1

- Mounting the CLV...................................................................4-7

- Mounting the distance sensors.....................................4-13

- Preparations.............................................................................4-1

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

SICK Advanced Series

Table of Contents

Related product manuals