Siemens SIMATIC S7-300 Module data - Page 511

Index
S7-300 Automation System Module data
Manual, 08/2006, A5E00105505-04
Index-5
Isochronous mode
SM 331,
6-35
SM 321, DI 16 x DC 24 V,
3-26
SM 332, AO 4 x 16 Bit,
6-114
SM 338,
7-11
L
Load restrictions in horizontal mounting position
SM 322, DO 8 x AC 120/230 V/2 A ISOL,
3-93
Load restrictions in vertical mounting position
SM 322, DO 8 x AC 120/230 V/2 A ISOL,
3-93
Load voltage L+ missing
SM 322, DO 8 x DC 24 V/ 0.5 A,
3-77, 3-79
Load voltage missing
Analog input module,
5-34
Analog output module,
5-34
M
Manual
purpose,
iii
Marine
Certification,
1-4
Measuring method
Analog input channels,
5-21
Analog input module,
A-8
Analog IO modules:,
A-42
SM 331, AI 8 x 13 Bit,
A-27
SM 331, AI 8 x 16 Bit,
A-35
SM 331, AI 8 x RTD,
A-16
SM 331, AI 8 x TC,
A-24
Measuring methods and ranges
SM 331, AI 2 x 12 Bit,
6-69
SM 331, AI 8 x 12 Bit,
6-57
SM 331, AI 8 x 13 Bit,
6-46
SM 331, AI 8 x 14 Bit High Speed,
6-33
SM 331, AI 8 x 16 Bit,
6-13, 6-22
SM 331, AI 8 x RTD,
6-79
SM 331, AI 8 x TC,
6-94
Measuring range
Analog input module,
A-8
Analog IO modules:,
A-42
SM 331, AI 8 x 13 Bit,
A-27
SM 331, AI 8 x 16 Bit,
A-35
SM 331, AI 8 x RTD,
A-16
SM 331, AI 8 x TC,
A-24
SM 334, AI 4/AO 2 x 12 bit,
6-145
Measuring range module,
5-21
reconnecting,
5-22
Measuring ranges
Analog input channels,
5-21
Mechanical environmental conditions,
1-8, 1-13
Mode of operation
SM 331, AI 8 x RTD,
A-15
SM 331, AI 8 x TC,
A-23
Module classes
ID,
B-2
Module error
SM 338, POS-INPUT,
7-20
Module not programmed
SM 321, DI 16 x DC 24 V,
3-30
Module overview,
6-3
Digital modules,
3-2
Other signal modules,
7-1
Monoflop time
SM 338, POS-INPUT,
7-16
Mounting rail
Dimensional drawing,
C-2
N
No parameters
SM 338, POS-INPUT,
7-20
Noise suppression
Analog input module,
A-8
SM 331, AI 8 x 13 Bit,
A-27
SM 331, AI 8 x 16 Bit,
A-34
SM 331, AI 8 x RTD,
A-15
SM 331, AI 8 x TC,
A-24
Non-isolated transducers,
4-5
wiring,
4-5
O
OB 40, 3-32, 5-35
Start information,
5-36
OB 82,
3-32, 3-81, 3-93, 3-107, 5-35
Operating state
of the CPU,
5-24
Operational limit,
5-26