Siemens SINUMERIK 840Di - Page 544

06.03
Index-544
 Siemens AG, 2003. All rights reserved
SINUMERIK 840Di Manual (HBI) – 06.03 Edition
Parameterizing axis-specific actual
values, 10-315
Parameterizing axis-specific setpoints, 10-315
Password
Resetting, 10-277
Setting, 10-277
PCU, 1-21
Interfaces, 1-21
Slots, 1-21
PCU 50, 2-81
PCU 70, 2-83
PDA area, 7-204
Performance data, PLC315-2DP, 8-251
Performance options, 1-20
PG/PC, 7-207
PHG, connecting/disconnecting during running
operation, 5-167
Pin assignment, cable distributor, 2-79
PIV area, 7-204
PLC module, 8-249
PLC MRES, 10-397
PLC operating state, 10-398
PLC program, 8-251
Loading, 8-255, 8-256
PLC RUN, 10-396
PLC RUN–P, 10-396
PLC start-up, 8-249
PLC STOP, 10-397
PLC system fault, 10-397
PLC Toolbox, 1-33
PLC user program, 8-251, 8-253
Plus, 1-20
Position control loop
Measurement, 13-427
Overshoots, 10-334
Reference frequency response, 13-427
Step height, 13-430
Position controller, 10-332
Position controller cycle, 10-290
Setting, 7-213
Position controller cycle offset, 10-290
Positioning accuracy, 10-289
Positioning axes, 10-328
Concurring, 10-328
Feedrate, 10-328
POWER
LED: ADI4, 2-118
LED: PP72/48, 2-101
Power OFF, 1-28
Power supply, 2-88
ADI4, 2-119
PP72/48, 2-101
PP72/48, 2-93
Setting the PROFIBUS address, 7-218
Preparing for start-up, 6-173
PROFIBUS
Modules, 2-45
Node address, 9-267
PROFIBUS address
Setting using an operator unit, 9-265
Setting using the PROFIBUS unit, 9-267
SIMODRIVE POSMO SI/CD/CA, 9-267
PROFIBUS DP, 10-393
General, 7-203
Interface, 1-21
PROFIBUS DP communication, 7-203
PROFIBUS S7 subnetwork ID, 9-269
Determining, 9-269
Programmable spindle speed limitations, 10-374
Proper shutdown, 10-306
Protection levels, 10-276
PTP link, 6-199
Pulse multiplication, 10-366
R
Ramp-up, 6-180, 6-181
After battery replacement, 6-183
First, 6-175
Ramp-up
After importing a backup copy, 6-186
After PCU/MCI board replacement, 6-186
After power failure, 6-186
After reinstallation/update, 6-185
After replacement of the MCI board, 6-183
Rapid traverse in JOG mode, 10-340
READY
LED: ADI4, 2-118
LED: PP72/48, 2-101
Real–time behavior , 10-398
Real–time property, 10-398
Real–time violations, 10-398
Real-time properties, 1-24
Real-time violations , 1-25
Redefining protection levels, 10-278
Reference point approach, 10-351
Resolutions, 10-281
Restart, 10-315
Retentive ranges, 8-258
Rotary axes, Drive optimization, 10-326
Rotary axis
With machine-mounted rotary
encoder, 10-318
With motor-mounted rotary
encoder, 10-318, 10-321
Rotary measuring system, 10-317
Routing information, setting, 9-269
RUN, 10-397
S
S1
Handwheel type, MCI board Ext., 2-63
PROFIBUS address, PP72/48, 2-95
Index